|
说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
|
|
1) Simulated program lesigning
仿真程序开发
2) parallel simulation program development environment
并行仿真程序开发环境
3) simulation program
仿真程序
1.
A simulation model of a heat pump using direct expansion solar energy collector was established and the simulation program which is used to analyze the effect of ambient,thermodynamic and construction parameters on heat pump system performance were written.
建立了混联式直接膨胀式太阳能辅助热泵的数学模型,并编制了仿真程序,分析了气象参数、结构参数和热力参数对热泵系统性能的影响;提出了热泵系统性能改进和运行控制的方向,可供该类系统的运行提供参考。
2.
In order to reduce development cost and reduce development cycle of combined balance,in accordance with the work principle of combined balance,the paper tells us how to compile simulation program of combined balance.
为了降低组合秤的研制成本,缩短研制周期,根据组合秤的工作原理,运用Visual Basic语言编写出组合秤仿真程序,重点介绍了仿真程序中单元质量分布数据产生以及组合计算的编程思想两个难点,具有较高的应用价值。
3.
In order to set a reasonable timeable of rail transit,it is normal that the operators rely on simulation programs.
为了制定合理的列车运行时刻表,运营管理人员必须借助于仿真程序。
4) Simulation Development
仿真开发
1.
This article brings forward a new model of developing embedded system with software simulation, Connecting SkyEye based on cygwin with Linux based on VMWare for Embedded System Simulation Development, not only saving hardware resources and money, but also surmount a series of disadvantages because .
本文提出了一种模拟开发嵌入式系统的软件模型,将运行在VMWare上的Linux与cygwin上的Sky-Eye连接起来进行嵌入式系统仿真开发,既节省了硬件资源又解决了资金问题,克服了开发人员由于不熟悉硬件所带来的一系列弊端,并对其可行性进行了较详细分析和论述,最后阐述了其应用前景。
5) emulator
[英]['emjuleɪtə(r)] [美]['ɛmjə'letɚ]
仿真器仿真程序
6) emulator
[英]['emjuleɪtə(r)] [美]['ɛmjə'letɚ]
仿真器,仿真程序
补充资料:Pro/E二次开发使用toolkit开发trigger的程序
使用toolkit开发trigger的程序时,往往需要能够连续通过trigger来触发dll中的函数. 我碰到的问题: 1.配置trigger: Name: CimDll Event: Create PIV Time: POST RequireNO DLL:Cim.dll Function:PDMTPIVCreatePostOperation 2.源代码: int PDMDLLInit() { PTCERROR pdm_status; FILE *g_pfileLog; g_pfileLog =fopen("test.dat","w"); setbuf(g_pfileLog,NULL); fprintf(g_pfileLog,"begin test\n"); pdm_status = PDMTriggerRegister("PDMTPIVCreatePostOperation", PDMTPIVCreatePostOperation); if (pdm_status != PDM_SUCCESS) { printf("Failed to Register Trigger PIV Create Post.\n"); } return (pdm_status); } int PDMTPIVCreatePostOperation(int argc, void **argv) { fprintf(g_pfileLog,"test\n"); ..... fprintf(g_pfileLog,"end test\n"); fclose(g_pfileLog); } 结果:以上代码存在的问题:如果我们在第一次checkin到C/S中后,删除test.dat文件,然后再进行checkin时,发现没有再生成test.dat,在函数PDMTPIVCreatePostOperation()中所进行的对文件的操作都无效. 原因:我们使用trigger触发时,真正起作用的是函数:PDMTPIVCreatePostOperation(),而PDMDLLInit()只是在第一次checkin时起作用,所以在第一次调用PDMTPIVCreatePostOperation()后,我就fclose(g_pfileLog),所以出现了上面的情况.所以注意的是:不要把一些重要的东西放在函数PDMDLLInit()中.
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条
|