1) Abrasive wear against water-sand slurry
水沙磨粒磨损
2) abrasive wear
磨粒磨损
1.
Study on abrasive wear resistance of boronized layer eutecticumed with laser;
激光共晶化渗硼层磨粒磨损试验研究
2.
Research on abrasive wear of cladding metal of flux cored wire for repairing of pedrail engineering machine;
履带式工程机械行走系修复用堆焊药芯焊丝磨粒磨损性能研究
3.
Two body abrasive wear mechanism of TiNi SMA;
TiNi 系形状记忆合金两体磨粒磨损机制研究
3) wear debris
磨损磨粒
1.
Study of Computer Identification and Analysis System for Wear Debris;
磨损磨粒的计算机识别分析系统研究
2.
In order to classify wear debris in lubricating oil more effectively,a wear debris recognition method based on rough set and neural network was put forward.
为了更有效地对润滑油中的磨损磨粒进行识别,探讨了基于粗糙集和神经网络的磨粒识别。
4) abrasion
[英][ə'breɪʒn] [美][ə'breʒən]
磨粒磨损
1.
The Ni60 flare remelting coating was formed by oxyacetylene flare,the abrasion resistance of remelting coating on N80 steel was compared with that on Ni60 under the same experiment condition.
利用氧-乙炔焰喷涂后重熔Ni60涂层,通过磨粒磨损试验,在相同的试验条件下,比较了N80钢和Ni60火焰喷涂后重熔涂层的耐磨粒磨损性能。
2.
A pearlitic steel and two kinds of white cast iron have been used in the abrasion test in HNO 3.
研究了1种珠光体钢及2种白口铸铁在硝酸中的磨粒磨损,结果表明:所有3种材料均发生了腐蚀与磨损相互催化的叠加作用,导致严重磨损。
3.
ATZW material has the hest abrasion resistance.
利用MLS-23型橡胶轮试验机测定了三种Al_2O_3+30m%TiC基复合陶瓷的磨粒磨损性能并分析了其磨损特点,结果表明,材料的磨损率随载荷的增加近似呈线性上升,磨粒硬度的高低对材料磨损率有较大的影响,ATZW复合陶瓷的耐磨性最好。
5) grain-abrasion
磨粒磨损
1.
In addition, the grain-abrasion performance of TLMW50 cladding material was tested by ML-10 grain-abrasion testing machine.
利用SEM、XRD对经1050℃~1100℃淬火、150℃~250℃回火的TLMW50覆层材料的组织进行分析研究,在ML-10磨粒磨损试验机上对TLMW50覆层的磨粒磨损性能进行测试,结果表明:经过淬火、回火处理的由珠光体+碳化物转变为马氏体+碳化物覆层组织得以不同程度的改善;覆层硬度相由烧结态的45。
2.
The shield machine cutter suffers from strong im- pact and grain-abrasion in high stress when it works in Bei- jing.
北京地区地铁施工时,盾构机刀具受到高应力作用下的冲击、磨粒磨损,损耗严重,进口刀具仅能掘进250m。
3.
Grain abrasion test was tested by grain-abrasion testing machine.
采用等离子熔覆技术,在Q235钢表面获得等离子熔覆高铬铁基复合涂层,利用OM、SEM、XRD、EDS分析了涂层的组织结构和相组成,用磨粒磨损试验机对其进行磨粒磨损试验。
6) abrasive
[英][ə'breɪsɪv] [美][ə'bresɪv]
磨粒磨损
1.
The variations in the abrasive resistance of high carbon steel (T12) before and after cryogenic treatment were investigated using an abrasive wear test rig (MLS 23) and hardness tester (HR 150D).
利用 MLS- 2 3型磨粒磨损试验机和 HR- 1 50 D型硬度计研究了深冷处理前后 T1 2高碳钢磨粒磨损性能的变化 ,并采用扫描电子显微镜对其微观形貌进行了观察和分析 。
2.
In this paper , the weldability and abrasive resistance of several surfacing electrodes have been analysed.
本文通过对堆焊焊条的焊接性和磨粒磨损性能的分析表明:含铬的堆焊焊条具有较好的耐磨性,但焊接性较差,只要能在马氏体基体上得到适当形貌的碳化物,其硬度和耐磨性均可达到中、高碳当量所能达到的性能,合金元素Mn改善堆焊焊条的耐磨性具有重要的作用。
3.
The wear mechanisms of the high temperature of the coatings are mounting and oxidation early , fatigue and abrasive afterwards.
涂层表面的磨损机制主要为开始以黏着磨损和氧化磨损为主,逐步过渡到以表面疲劳磨损和磨粒磨损为主。
补充资料:磨沙
1.指沙入蚌壳,与蚌肉相摩擦。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条