1) temperature deformation coeffi cient
温度变形系数
1.
Lowering temperature deformation coeffi cient can reduce temperature deformation and thus reduce temperature stress.
混凝土具有热胀冷缩的性质,混凝土的温度变形系数随所用骨料的种类及配合比的不同而变化,但其变化不大,一般在6×10-6/℃～13×10-6/℃之间。
2) temperature varying coefficient
温度变化系数
3) temperature coefficient of gauge factor(TCGF)
应变系数的温度系数(TCGF)
4) thermal deformation
温度变形
1.
It is very important to study the thermal deformation occurring in mass concrete and its super-long structures,the cause of which must be made clear before studying the thermal performance of concrete.
混凝土结构温度变形性能在大体积混凝土及超长结构中非常重要,研究混凝土材料的温度变形性能有必要清楚其温度变形产生的本质。
2.
The main factors, such as limiting extended value, elastic module and thermal deformation of the influence on crack resistance of mass concrete have been analyzed in this paper.
对影响大体积混凝土抗裂性的极限拉伸值、抗拉弹性模量、温度变形等几个主要因素进行了分析,得出大体积混凝土抗裂性指标,并将其应用于评价大体积混凝土抗裂性,结果与实际工程相符,可靠有效。
3.
The main factors,including lim it ing extended value,elastic module and thermal deformation,which influenc on cr ack re sistance of mass concrete have been analyzed in this paper.
本文对影响大体积混凝土抗裂性的极限拉伸值、抗拉弹性模量、温度变形等几个主要因素进行了分析,得出大体积混凝土抗裂性指标,并将其应用于评价大体积混凝土抗裂性,结果与实际工程相符,可靠有效。
5) deformation temperature
变形温度
1.
Effect of deformation temperature on dynamic recrystallization of ULCB steel;
变形温度对ULCB钢动态再结晶的影响
2.
Influence of deformation temperature on the critical strain for completion of DEFT;
变形温度对形变强化相变完成时临界应变量的影响
3.
A new fractal method for the determination of deformation temperatures and strain rates-A case study of the Fuchashan tectonite in the Tanlu fault;
确定变形温度和应变速率分形法的探讨——以郯庐断裂浮槎山构造岩为例
6) Deforming Temperature
变形温度
1.
Effect of Deforming Temperature on Structure and Precipitates of 0.05C-0.13Nb Steel;
变形温度对0.05C-0.13Nb钢组织和析出物的影响
2.
The static softening in interval time increased with the increasing of deforming temperature,interval time and deformation,re-crystallization of austenite was easier to occu.
利用MMS-100热力模拟试验机研究了X60管线钢和JB700低碳贝氏体钢在不同变形温度、变形程度和变形后等温保持时间对奥氏体静态软化行为的影响。
3.
In this paper,with uniaxial tensile test of AA5083 aluminum alloy,we analyze and discuss the influence of deforming temperature and strain rate on elongation.
通过对铝合金AA5083超塑性材料的拉伸试验,分析和讨论了变形温度和应变速率对其延伸率的影响,并得到最佳温度525℃,最佳应变速率1。
补充资料：变形区形状系数
变形区形状系数
parameters of deformation zone
b ianxingqu xingzhuang xishu变形区形状系数(parameters of deformationzone)通常指反映变形区几何特征及这些特征在轧制过程中对应力状态影响程度的轧件和工具尺寸的。~一~一，二。，了二H十川，，，。小二，，~参数，主要有z仄、R仄(万一号二}，H/D或从/D。式中D、R、H、h、万、l分别指轧辊直径、轧辊半径、轧件轧前厚度、轧件轧后厚度、轧件平均厚度、变形区长度。 (余望)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条