1) elastic modulus of main cable
主缆弹性模量
2) Young's modulus
弹性模量
1.
Young's modulus and interface fracture toughness of metal-base ceramic coatings;
金属基陶瓷涂层弹性模量和界面断裂韧度
2.
The Young's modulus and stress rupture lives of single crystal alloys also exhibit obvious anisotropy.
结果表明,晶体取向对合金枝晶组织形态和偏析存在显著影响,而合金的弹性模量和持久性能也存在明显的各向异性。
3.
The Young's modulus in different directions of the films were calculated based on phenomenological theory and orientation distribution function (ODF).
计算了薄膜试样不同方向的弹性模量,研究了织构和甲烷浓度对CVD自支撑金刚石薄膜的宏观残余应变的影响。
3) elasticity modulus
弹性模量
1.
If seismic method can detect the changing of elasticity modulus in target strata,it will no doubt help us further understand the development of fractures.
当岩石中含有裂缝时,岩石的弹性模量(主要指体模量、剪切模量、泊松比以及地震波的速度)会发生变化,而且这种弹性模量的变化又随裂缝中是否含有流体而不同。
2.
In this paper, parameters to evaluate the dynamic mechanical property of oil well cement stone are determined to be elasticity modulus aod crashing absorption energy.
确定了水泥石的动态力学性能评价参数为水泥石的弹性模量和水泥石的破碎吸收能。
3.
particle board's elasticity modulus.
针对刨花板、定向刨花板、重组木等碎料板弹性模量的微观力学求解理论进行综述,提出各个板种微观力学模型建立的原则,指出相应的数学模拟计算理论与方法的研究方向,编制计算机仿真计算软件库。
4) elastic modulus
弹性模量
1.
Hardness and elastic modulus of microcastings by nanoindentation;
纳米压痕法测定微铸件硬度及弹性模量
2.
Modified method for the prediction of effective elastic modulus of composite materials;
复合材料等效弹性模量预测方法的改进
3.
Analysis on elastic modulus test of polyaramid fiber yarns;
有机纤维束纱弹性模量测试分析
5) elastic module
弹性模量
1.
The influence of autoclave sterilization on elastic module and flexural strength of five types of posts;
高温高压消毒对五种桩挠曲强度与弹性模量的影响
2.
Test-study for the elastic module of concrete with long age under the action of fatigue loads;
疲劳荷载作用下长龄期混凝土弹性模量的试验研究
3.
The result of analysis shows that the magnitude of in situ stress has the trend to increase with the increasing of the depth and the elastic module of rock mass,but the relation between the in situ stress and elastic module is not so close as the relation between the in situ stress and depth.
结果表明,地应力值随岩体的埋藏深度和弹性模量的增加而增大,但地应力与岩体弹性模量的关系远不如它与岩体埋藏深度的关系那样有良好的线性关系。
6) modulus of elasticity
弹性模量
1.
Influence of modulus of elasticity on the forming precision of lapping tools in the aspherical lapping of bending formation method;
弹性模量对弯曲成形法非球面研磨中磨具成形精度的影响
2.
Study on the modulus of elasticity of composite pad bushed thrust-bearing;
复合材料瓦面推力轴承弹性模量的研究
3.
Simulated annealing-based BP neural network optimization method for back analysis of modulus of elasticity for slope rock mass;
边坡弹性模量反分析的模拟退火BP网络方法
补充资料:表观弹性模量
分子式:
CAS号:
性质: 在减震橡胶制品中,由于橡胶与金属黏着界面的形状效应,不能仅由形状尺寸和橡胶的弹性模量来决定不同方向的弹簧常数,为此将表观弹性模量Eap定义为:圆柱形:Eap=(3+4.9355S2)G正方形:Eap=(3+6.580S2)G无限长柱:Eap=(4+3.290S2)G式中G为剪切弹性模量,S为形状因子。
CAS号:
性质: 在减震橡胶制品中,由于橡胶与金属黏着界面的形状效应,不能仅由形状尺寸和橡胶的弹性模量来决定不同方向的弹簧常数,为此将表观弹性模量Eap定义为:圆柱形:Eap=(3+4.9355S2)G正方形:Eap=(3+6.580S2)G无限长柱:Eap=(4+3.290S2)G式中G为剪切弹性模量,S为形状因子。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条