1) Liquid Infiltration-Extrusion
液态浸渗挤压
1.
The FEM Simulation of the Liquid Infiltration-Extrusion Process Including Damage for Composites;
复合材料液态浸渗挤压有限元模拟及损伤研究
2.
The FEM Simulation of the Liquid Infiltration-Extrusion Process for Composites;
复合材料液态浸渗挤压过程的有限元模拟
3.
Research on the FEM Simulation of the Liquid Infiltration-Extrusion Process for Fabricating MMC;
液态浸渗挤压复合材料过程的有限元模拟
2) squeeze infiltration
挤压浸渗
1.
Al2O3-SiO2/AZ91D composites were fabricated by squeeze infiltration process.
采用挤压浸渗法制备Al2O3-SiO2/AZ91D复合材料。
3) liquid infiltration
液态浸渗
1.
Both the load and the displacement of the ram as well as their relationship during extrusion which directly follows liquid infiltration were experimentally measured and analyzed.
实验测定分析了液态浸渗后直接挤压过程的冲头载荷与位移关系曲线及它们各自随时间的变化，指出了不同工艺条件下所获得的载荷－位移曲线存在很大差异的原因，揭示了工艺参数对液态浸渗后的挤压过程性质有着决定性作用。
2.
A numerical simulation technique based on the stable alternating direction implicit (SADI) method and the upper bound element technique(UBET) is presented and applied to simulations of extrusion directly following liquid infiltration which involves infiltration,solidification, and large plastic deformation in one process.
采用稳定的交替方向隐式（ＳＡＤＩ）有限差分方法、上限元法（ＵＢＥＴ）等数值计算方法模拟了融浸渗、凝固和大塑性变形为一体的液态浸渗后直接挤压的工艺过程。
4) infiltration
[英][,infil'treiʃən] [美][,ɪnfɪl'treʃən]
液态浸渗
1.
Mechanical Properties of Alumina Short Fiber Reinforced Aluminium Matrix Composites Fabricated by Extrusion Directly Following infiltration;
液态浸渗后直接挤压铝基复合材料的力学性能
2.
Infiltration process of fiber reinforced magnesium aluminium matrix composites made by liquid infiltration was mainly studied in the paper.
本文着重研究了液态浸渗法制备纤维增强镁、铝基复合材料的浸渗工艺。
5) liquid extrusion
液态挤压
1.
Analysis on flow velocity and equivalent strain of the metal in the process of liquid extrusion;
液态挤压过程中金属流动速度与等效应变的分析
2.
Numerical simulation of infiltration process in liquid extrusion for fabrication of Al_2O_3f /LY12 composites;
液态挤压制备Al_2O_(3f)/LY12复合材料浸渗过程的数值模拟
3.
Using liquid extrusion to manufacture the aluminum-alloy grip, taking the place of hot die forging, can greatly increase the material utilization rate, reduce the processing procedures and lower the product cost.
采用液态挤压代替热模锻生产铝合金钳柄体 ,可显著提高材料利用率、减少成形工序及降低产品成本。
6) liquid metal infiltration
液态浸渗法
1.
Development of the carbon fiber reinforced magnesium matrix composites fabricated by liquid metal infiltration;
液态浸渗法制备碳纤维增强镁基复合材料研究进展
补充资料：液态挤压
液态挤压
liquid state extrusion
yetoiJ一ya液态挤压(liquid state extrusion)将液态金属注入一端被封闭的挤压筒内直接挤压成形的金属塑性加工方法。液态金属挤压主要是在立式挤压机(见图)上进行，同固态金属挤压相比较可省力、节能。通常应用于电缆外皮包铅及生产电工用保险丝。沁 液态金属挤压 1一模;2一挤压筒;于一挤压杆;4一芯棒 (温景林)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条