2) ball pin part
球销零件
1.
The ball pin part is the key part of ball pin universal coupling .
球销零件是球销万向联轴器的关键零件,加工中零件不易夹紧,加工费时费力,存在加工精度差、不易互换等缺点。
3) pin parts
销钉零件
4) spherical part
球形零件
1.
Non-innerwrinkling criteria for spherical part drawing wit h blank holder are set up by use of an amended innerwrinkling model,with geometric conditions and analysis of stress-strain taken into consideration.
本文利用修正了的内皱模型,结合拉深过程中的几何条件及应力应变分析,推导了在平面压边情况下球形零件拉深过程中不发生内皱的判据;进而求解出拉深过程中克服内皱的最小压边力。
5) shaft parts
轴类零件
1.
Numerical simulation on cross wedge rolling of shaft parts with eccentric section;
偏心圆截面轴类零件的楔横轧成形数值模拟
2.
Research on shaft parts straightening technology general predictive multi-steps algorithm;
轴类零件校直工艺广义预测多步算法研究
3.
The Parametrization Design for the Shaft Parts with Auto CAD;
基于AutoCAD的轴类零件参数化设计
6) shaft part
轴类零件
1.
The key problems and its research development trends of shaft parts' automatic cold straightening technology theory;
轴类零件自动校直技术现状及发展趋势
2.
Proposes a new method based on searching minimum anti-clockwise angle to identify outline of shaft part drawings.
提出了识别轴类零件外轮廓的逆时钟最小夹角法,讨论了五种特殊角度计算及多对象相切情况的处理方法,确定了轮廓点的搜索原则和中心线的处理方法。
3.
The paper develops the computer aided drawing systems on shaft parts based on AutoCAD2004 by using second development systems and their pull-down menu and VLISP language.
介绍在AutoCAD2004平台上,利用二次开发系统及其下拉菜单、VLISP语言等控制模块程序而开发轴类零件图绘制系统。
补充资料：机械类常用英语：冲压模具-零件类
punch冲头
insert入块(嵌入件)
deburring punch压毛边冲子
groove punch压线冲子
stamped punch字模冲子
round punch圆冲子
special shape punch异形冲子
bending block折刀
roller滚轴
baffle plate挡块
located block定位块
supporting block for location
定位支承块
air cushion plate气垫板
air-cushion eject-rod气垫顶杆
trimming punch切边冲子
stiffening rib punch = stinger 加强筋冲子
ribbon punch压筋冲子
reel-stretch punch卷圆压平冲子
guide plate定位板
sliding block滑块
sliding dowel block滑块固定块
active plate活动板
lower sliding plate下滑块板
upper holder block上压块
upper mid plate上中间板
spring box弹簧箱
spring-box eject-rod弹簧箱顶杆
spring-box eject-plate弹簧箱顶板
bushing bolck衬套
cover plate盖板
guide pad导料块
insert入块(嵌入件)
deburring punch压毛边冲子
groove punch压线冲子
stamped punch字模冲子
round punch圆冲子
special shape punch异形冲子
bending block折刀
roller滚轴
baffle plate挡块
located block定位块
supporting block for location
定位支承块
air cushion plate气垫板
air-cushion eject-rod气垫顶杆
trimming punch切边冲子
stiffening rib punch = stinger 加强筋冲子
ribbon punch压筋冲子
reel-stretch punch卷圆压平冲子
guide plate定位板
sliding block滑块
sliding dowel block滑块固定块
active plate活动板
lower sliding plate下滑块板
upper holder block上压块
upper mid plate上中间板
spring box弹簧箱
spring-box eject-rod弹簧箱顶杆
spring-box eject-plate弹簧箱顶板
bushing bolck衬套
cover plate盖板
guide pad导料块
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条