1) two-phase single-point intersection
二相位单点交叉口
2) isolated intersection
单点交叉口
1.
Optimal time assignment of traffic signal cycle in isolated intersection;
单点交叉口信号灯优化配时研究
3) phase crossover
相位交(叉)点
4) two-phase intersection
两相位交叉口
1.
Method of computing left-turn vehicle traffic capacity at two-phase intersection;
两相位交叉口左转车通行能力计算方法
2.
Conflict delay models at two-phase intersection
两相位交叉口车辆冲突延误模型
5) multi-phase intersection
多相位交叉口
1.
Fuzzy control method in multi-phase intersections based on variable phase sequence was put forward,which can effectively improve the traffic capacity of intersection and reduce vehicle delay.
提出一种基于可变相序的多相位交叉口模糊控制方法,合理选出优先权较大的相位作为放行相位。
6) isolated intersection
单交叉口
1.
Multi-strategy based fuzzy control algorithm and its optimization for isolated intersection;
单交叉口多策略模糊控制算法与优化
2.
A Pass Through Need Degree-based Isolated Intersection Fuzzy Control Algorithm;
一种基于通行需求度的单交叉口模糊控制算法
3.
Aiming at the current problems accorded on isolated intersection traffic lights, a traffic lights controller using fuzzy control for an isolated intersection was presented here, and the over all design based on programmable logic devices is given in detail.
针对城市单交叉口交通信号控制问题,提出了一种应用模糊控制理论的单交叉口交通灯控制器,并给出了基于大规模可编程逻辑器件的完整设计实现方案。
补充资料:闭式单点、双点压力机
| |||||||
主要参数内容 | 国际先进 | 国内先进 | 国内一般 | 国内落后 | 评定方法及说明 | ||
(一)加工精度 | 参照GB10924-89、GB10933-89、JB5200-91 | ||||||
1、滑块下平面对工作台上平面的平行度(mm) | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
0.02+0.10/100×滑块下平面的被测长度 | |||||||
2、滑块行程对工作台上平面的垂直度 | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
0.05+0.02/100×滑块行程长度 | |||||||
(二)结构性能 | |||||||
1、离合器、制动器接通率,当滑块行程次数≤16次/分时为70%,≤25次/分时为60%,≤45次/分时为50% | 大于规定值10% | 大于规定值 | 达到规定值 | 达不到规定值 | |||
2、液压超负荷保险装置、微调装置、吨位指示器 | 全部具有 | 全部具有 | 部分具有 | 没有 | |||
(三)噪声dB(A) | |||||||
1、公称力≤400kN | ≤85 | ≤87 | ≤88 | >88 | |||
2、公称力>400kN | ≤87 | ≤88 | ≤90 | >90 | |||
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条