1) electro-kinetic mass transport
电动传递
2) electropneumatic transmitting equipment
电动气动传递设备
3) momentum transfer
动量传递
1.
This paper is mainly based on momentum transfer of solid particles during acceleration,and ascertains the qualities and velocities changes of water and solid particles with each other during momentum change,including outside factors influencing their momentum change.
以固体颗粒在加速过程中发生的动量传递为出发点,确定了相互发生动量交换的清水、固体颗粒的质量及其速度变化量,及影响其动量变化的外界因素。
2.
In addition, the momentum transfer on the V-grid tray and its effect on clear liquid height and hydraulic gradient cross tray are discussed.
通过对塔板上气、液两相间的动量传递进行分析，讨论了动量传递对液面落差和清液层高度的影响。
3.
With the dimentional analysis, the fluid momentum transfer resistance criterion(R_L~*, RL), the heat transfer resistance criterion(R_H~*,R_H), the mass transfer resistance criterion R_M~*, R_M [*: denotes unsteady state], the buoyance resistance criterion R_(by) and the liquid membrane energy criterion E_σ were derived from the principal physical parameter of ILM.
应用因次分析法,由ILM的主要物理参数导出了流体动量传递阻力准数R_L~*、R_L,热量传递阻力准数R_H~*、R_H,质量传递阻力准数R_M~*、R_M(*代表非定常),浮阻准数R_(by)和膜能准数E_σ。
4) vibration transfer
振动传递
1.
Two thrust bearings vibration transfer characteristics are studied.
针对目前舰船上大多采用的米契尔式推力轴承所带来的振动问题,提出采用新型法兰盘式推力轴承的思路;对两型推力轴承推进轴系的振动传递特性进行对比分析;结果显示:两型推力轴承推进轴系的纵向振动特性相似,但法兰盘式推力轴承能有效衰减推力轴承基座振动向船体的传递,具有较好的减振降噪效果。
2.
This paper presents a network model of a vibration transfer system in multi input and multi output, and also proposes a maximum capacity algorithm of finding N mainpaths in a vibration transfer system.
建立了多输入多输出振动传递系统的网络模型，并给出了求Ｎ条振动传递主途径的最大容量算法。
3.
This paper establishes the network optimization model and mathematical programming model of a vibration transfer system with multi input and single output, presents a stage maximum flow algorithm of finding the total vibration transfer information, and discusses the properties and characteristics of a most common vibration transfer system with multi input and single output.
建立了多输入单输出振动传递系统的网络优化模型和数学规划模型，给出了一种求振动传递总信息的分层极大流算法。
5) motion transmission
运动传递
6) power transmission
动力传递
1.
Aiming at the most design for current rollermills according to the experience and lack of basic design data for working state,the force situation of the rollers was analyzed and calculated through study on the rule of power transmission in a rollermill.
针对目前磨粉机的设计大多根据经验进行,缺乏工作状态的基础设计数据的状况,通过研究辊式磨粉机磨辊动力传递的规律,分析计算了磨辊的受力情况;运用有限元分析软件ANSYS建立了磨辊的物理分析模型,并进行了强度计算分析,结果显示了磨辊在稳态工作状态下的应力应变情况。
补充资料：z-传递函数
分子式：
CAS号：
性质： 对于单变量线性定常离散系统，初始条件为零时，系统输出变量的z变换与输入变量的z变换之比称为离散系统的z传递函数，或脉冲传递函数。
CAS号：
性质： 对于单变量线性定常离散系统，初始条件为零时，系统输出变量的z变换与输入变量的z变换之比称为离散系统的z传递函数，或脉冲传递函数。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条