1) Nitinol stent
镍钛支架
2) Nickel Titanium
镍钛
1.
Methods Tracheostomy with and without nickel titanium shape memory alloy stent was performed following total laryngectomy.
方法 分别用镍钛记忆合金气管造口支架埋置法和单纯气管造口法在全喉切除时行Ⅰ期造口成型 ,6个月后比较它们的造口平均直径及呼吸、排痰功能的顺畅程度。
3) NiTi alloy
镍钛合金
1.
Application of NiTi alloy bronchial occlusive device in bronchial fistula occlusion;
镍钛合金支气管封堵器在支气管瘘封堵中的应用
2.
Phase transformation from austenite to martensite in NiTi alloy strips under uniaxial tension has been observed in experiments and has been numerically simulated as a localized deformation.
单向拉伸镍钛合金带中从奥氏体到马氏体的相变已在实验中观测到,并被看作为局部变形进行了数值模拟。
3.
This paper describes the biomimetic synthesis of calcium phosphate composite coating with chitosan on NiTi alloy.
将高浓度模拟体液5×SBF与壳聚糖溶液相互结合,在预处理后的镍钛合金基体上快速形成了含壳聚糖的钙磷复合涂层。
4) Nickel-titanium wire
镍-钛丝
5) NiTi alloys
镍钛合金
1.
The surfage modification of NiTi alloys grafted by silylation MPEG;
硅烷化甲氧基聚乙二醇接枝改性镍钛合金
2.
A coating on NiTi alloys surfaces was prepared under diethylene glycol dimethyl ether (diglyme) microwave cold-plasma in electron cyclotron resonance conditions.
在微波电子回旋共振低温等离子体条件下,用二乙二醇二甲醚为试剂对镍钛合金进行表面改性。
3.
However, NiTi alloys have high resistance to deformation, low thermo-conductivity, non-uniform deformation during hot processing.
本文着重进行了以下几个方面的研究: 采用DEFORM-3D商用软件对镍钛合金管坯等温挤压过程进行数值模拟分析。
6) nitinol
镍钛合金
1.
Experimental Study of Vascular Anastomosis with Nitinol Clip;
镍钛合金吻合夹吻合血管的实验研究
2.
Low cycle fatigue failure with large strain of nitinol has been tested.
对镍钛合金进行了低周大应变疲劳试验,研究了板厚、丝径大小、表面处理工艺、热处理制度、冷热拉伸、形变角幅度、熔炼工艺等对低周疲劳寿命的影响。
3.
Methods The device was constructed from superelastic Nitinol wires tightly woven into two flat disks and sewed with polyester fibers inside,with a pliable loop on the right-atrial-disk of the device,connecting to the delivery cable.
方法自行设计封堵器是由镍钛合金丝编织成的网状结构,外形呈双盘状,其左房面平整,右房面中间凹陷,中央有与推送杆相接的连接袢,内衬有三层聚酯膜。
参考词条
补充资料：镍钛温度记忆合金支架
镍钛温度记忆合金支架
介入放射学器材。一种热记忆合金支架。其特点是具有形状记忆功能，低温下非常柔软，置入靶部位后在体温下恢复设定的形状。用于治疗血管和空腔脏器的狭窄。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。