1) rectangular mini-channels
细矩形通道
1.
The influence of variable fluid thermal properties and average fluid thermal properties on flow and heat transfer in rectangular mini-channels had been investigated numerically by using fluid- solid conjugate heat transfer technologies and second development technologies of CFD.
以细矩形通道为研究对象,基于CFD的二次开发技术,采用流体固体共轭传热技术数值研究了流体变物性和入口平均物性对细矩形通道平均流动和平均传热特性的影响,同时研究了流体变物性对细通道转捩雷诺数的影响,为进一步揭示微细通道的流动和传热机理提供了依据。
2) rectangular channel
矩形通道
1.
A set-up for test of fluid flow friction characteristic was designed and built,which was used to measure the flow parameters for the rectangular channel with the staggered holed-baffles.
设计和建立了一套流动阻力特性试验装置,对流体流经交错布置多个开孔折流板的矩形通道时的阻力特性进行了测试。
2.
The flow and heat transfer in a rectangular channel with a flat heated plate in the middle section was experimentally investigated.
通过实验研究了中心截面带有加热平板的水平和倾斜矩形通道入口段的混合对流换热,该矩形通道和加热平板均采用高热导率材料制作,矩形通道外壁面绝热。
3.
An analytical study has been done on the critical heat flux (CHF) in the rectangular channel with a closed bottom, in which a liquid film and a vapor flow exist in a countercurrent annular flow.
分析研究了在底部封闭矩形通道内逆流汽液两相流条件下的临界热流密度的发生机理。
3) rectangular duct
矩形通道
1.
A theoretical investigation is presented for fully developed flow of power law fluid through a rectangular duct,this modelling is based upon the Patankar's control volumemethod -a famous numerical simulation method of fluid flow and heat transfer.
针对假塑性幂律流体在矩形通道中充分发展流动问题,用帕坦卡方法作数值分析,文中讨论了不等距网格的划分方法和粘度系数的插值方法。
2.
The mixed convection heat transfer of the entrance region in a vertical rectangular duct with a uniformly heated plate was experimentally investigated when the forced air flowed upward and downward.
通过实验研究了内置均匀加热板的垂直矩形通道入口段混合对流换热的温度场和阻力特性。
3.
A numerical study is conducted for laminar flow heat transfer in rectangular ducts in thethermal entrance region with one side heated and three sides adiabatic.
对单面加热矩形通道热入口段的层流对流换热问题进行了数值模拟研究,给出了不同截面比的局部努赛尔数。
4) rectangular microchannel
矩形微通道
1.
Three dimensional simulation for steady annular condensation in rectangular microchannels;
矩形微通道中环状冷凝的三维数值模拟
2.
This paper investigated the behaviors of flow and heat transfer of single-phase in rectangular microchannels with three-dimensional numerical analysis.
本文针对矩形微通道内单相流动和传热特性,利用CFD模拟分析软件对其进行三维数值模拟研究。
5) Double narrow rectangular channels
矩形双通道
1.
Nonlinear research of flow oscillation in double narrow rectangular channels;
矩形双通道间脉动的非单值性试验研究
6) rectangular narrow channel
矩形窄通道
1.
Heat transfer enhancement in rectangular narrow channel with longitudinal vortex generators;
矩形窄通道内带纵向涡发生器的传热强化
补充资料：染料细粉及超细粉
分子式：
CAS号：
性质：非水溶性染料或不易溶染料常采用的剂型。如分散染料、还原染料等对粒度及粒度分布均有一定要求，要求相对集中，过细、过粗，均对使用有不良影响。染料生产企业对本企业的产品均作了规定。这些染料产品一般多在2μm到上到4μm范围内，如对某些分散染料要求控制在1μm左右，分散性能4～5级，还原染料也与分散染料近似，故有超细粉之称。为使染料产品达到上述细度，常采用万能粉碎机或砂磨、球磨等进行粉碎。
CAS号：
性质：非水溶性染料或不易溶染料常采用的剂型。如分散染料、还原染料等对粒度及粒度分布均有一定要求，要求相对集中，过细、过粗，均对使用有不良影响。染料生产企业对本企业的产品均作了规定。这些染料产品一般多在2μm到上到4μm范围内，如对某些分散染料要求控制在1μm左右，分散性能4～5级，还原染料也与分散染料近似，故有超细粉之称。为使染料产品达到上述细度，常采用万能粉碎机或砂磨、球磨等进行粉碎。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条