1) plastic part with thread
螺纹塑件
1.
Analyzed the structure characteristics and quality request of the plastic part with thread, elaborated mold design key points and working process in detail.
分析了螺纹塑件的工艺结构及品质要求,详细阐述了该螺纹塑件注射模的结构设计要点与工作过程,通过使用齿条、齿轮组合的脱模机构,使得模具的使用寿命和可靠性大大提高。
2) thread part
内螺纹塑件
3) internally threaded mo(u)ld part
内螺纹模塑件
4) Plastic thread tube
塑料螺纹管
1.
Conclusion Plastic thread tube has significantly decreased anastomotic leak,complication is low,hospitalization is short,q.
方法 回顾分析了 42例应用塑料螺纹管Ⅰ期修复左半结肠损伤的临床资料 。
2.
Conclusion Plastic thread tube has raised significantly the successful ra.
方法 采用塑料螺纹管对低位直肠癌行结肠 肛管吻合术 (Parks) 。
5) screw element
螺纹元件
1.
Blend morphology of polymer at outlet of common screw element in an intermeshing co-rotating twin screw extruder Ⅰ.Computation of three-dimensional particle trajectories;
啮合同向双螺杆挤出机普通螺纹元件末端共混物的混合形态 Ⅰ.物料三维流动路径的计算
2.
Blend morphology of polymer at outlet of common screw element in co-rotating intermeshing twin-screw extruder Ⅱ.Blend morphology computation;
啮合同向双螺杆挤出机普通螺纹元件末端共混物的混合形态 Ⅱ.混合形态的计算
3.
The elements, named as screw element and crossing plate element, were developed based on a better understanding of mixing mechanism of rotating Kenics mixing element, and the mixing performance of the elements in reaction injection molding was tested.
结果表明,开发的螺纹元件能够取得与Kenics混合元件相近的混合效果,所得制件表面质量最好;而交错平板元件混合效果差,反应不均匀,反应速度慢;旋转式Kenics混合元件的螺旋结构产生的拉伸和剪切在混合过程中起主要作用,交错平板结构的分割作用是次要的。
6) thread insert
螺纹嵌件
1.
Through analyzing the problems in mold design of thread insert,proposed the solution of think invensely,designed mold structure with thread insert,successfully solved the problems of the thread insert.
通过对螺纹嵌件模具设计中存在问题的分析,提出了逆向思维的解决方法,设计出了弹性接触的模具结构,成功地解决了螺纹嵌件的问题。
补充资料：螺纹管件
分子式：
CAS号：
性质：带螺纹的管件。常用于水煤气管、小直径水管、压缩空气管和低压蒸汽管等。与带螺纹的管端联接而成管路。螺纹上可涂以适当的胶合剂(如厚白漆、一氧化铅甘油胶合剂等)，以保证密封。主要有内牙管、外牙管、活管接、肘管(弯头)、三通管、四通管(十字头)和异径管等。
CAS号：
性质：带螺纹的管件。常用于水煤气管、小直径水管、压缩空气管和低压蒸汽管等。与带螺纹的管端联接而成管路。螺纹上可涂以适当的胶合剂(如厚白漆、一氧化铅甘油胶合剂等)，以保证密封。主要有内牙管、外牙管、活管接、肘管(弯头)、三通管、四通管(十字头)和异径管等。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条