1) anti-compressive stiffness structure
抗压刚度结构
2) tensile(compressive) stiffness of member
构件抗拉(抗压)刚度
3) tensile(compressive stiffness of member)
构件抗拉(抗压刚度)
4) compressive stiffness
抗压刚度
1.
Considering the elastic compressive deformation of foundation pile with changes in cross section,the characteristics of soil around pile and soil resistance at pile tip,influencing coefficient of compressive stiffness is put forward with respect to pile length and pile tip resistance.
考虑变截面桩的弹性压缩变形、桩周土和桩端土特性,提出了桩长和桩端土阻力对桩端位移的影响 系数,利用变分原理推导出了基桩抗压刚度计算公式,计算值与工程实例测试值吻合较好。
2.
Based on the compatibility of radial displacement and longitudinal strain, the compressive stiffness of CCFST is derived.
将复式钢管砼空心柱分成核心砼、内钢管和外钢管3部分,通过对核心砼进行轴对称柱体分析和钢管的薄壳分析,考虑核心砼和内、外钢管的径向位移和纵向应变的协调条件,建立了复式钢管砼空心柱抗压刚度EA的计算公式。
3.
Based on the compatibility of radial displacement and longitudinal strain, the compressive stiffness of CFST is derived.
将钢管混凝土分成混凝土和钢管两部分,通过对混凝土进行轴对称柱体分析和钢管的薄壳分析,考虑钢管和混凝土径向位移、纵向应变协调,建立了钢管混凝土结构抗压刚度EA的计算公式,并与试验结果及其他计算方法进行比较,同时分析了钢管和混凝土的泊松比对钢管混凝土抗压刚度的影响。
5) structural stiffness
结构刚度
1.
Combined with project survey,it analyzes the reasons generating crack on the board casting in place of house from the aspects of the structural stiffness break,not installing desirable dilatation joint,steel bar fall on bearing,temperature,shrinkage etc,and brings forward corresponding prevention measures,which will eradicate the crack on the board casting in place.
结合工程概况,从结构刚度突变及未设置必要的伸缩缝、支座处负筋下沉、温度、收缩等方面分析了住宅现浇板裂缝的产生原因,并提出了相应的防止措施,以彻底根除现浇楼板的裂缝。
2.
A simplified formula was developed to calculate the local structural stiffness of each bump of the bump foil with the consideration of frictions between bump foil and its contact surfaces,and the influences of different parameters on the structural stiffness were analyzed.
考虑波箔轴承中波箔与接触面间摩擦力的影响,得出了计算波箔局部结构刚度的简化公式,并分析了影响波箔轴承结构刚度的参数。
3.
Using the concept of load capacity coefficient,the effect of the variations of structural stiffness in circumferential,axial and radical directions on the performance of load capacity of foil bearing were analyzed.
从承载力系数出发,分析了箔片轴承在周向、轴向和径向3个空间方向的结构刚度的变化对箔片轴承承载力的影响。
6) structure rigidity
结构刚度
1.
The criteria of conceptual design on high-rise building structure rigidity are introduced in this paper.
阐述了高层建筑结构刚度的概念设计原则和结构刚度与震害的关系,分析了规范对结构刚度的规定,并进一步提出了对结构刚度的认识,可供高层建筑结构设计人员参考借鉴。
补充资料：抗挠刚度
分子式：
CAS号：
性质：纸或纸板抵抗弯曲的强度性能。挺度与EI/W值成正比，其中W、E和I分别为纸或纸板的质量、弹性模量和惯性矩。纸板的挺度或称抗挠刚度，是指在距夹具5cm处对垂直夹着的试样施加一定负荷，观察从试样中心线弯曲3.81mm宽度，试样至15°所需的弯矩，以g·cm表示。对箱板纸和白板纸来说，挺度是一项基本性能指标。
CAS号：
性质：纸或纸板抵抗弯曲的强度性能。挺度与EI/W值成正比，其中W、E和I分别为纸或纸板的质量、弹性模量和惯性矩。纸板的挺度或称抗挠刚度，是指在距夹具5cm处对垂直夹着的试样施加一定负荷，观察从试样中心线弯曲3.81mm宽度，试样至15°所需的弯矩，以g·cm表示。对箱板纸和白板纸来说，挺度是一项基本性能指标。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条