1) point-fixed glass
点支式玻璃
1.
In this paper,familiar quality problem of point-fixed glasses roof is posted,essential reason of various kinds of breakage phenomenon is analyzed,Several reasonable disposal measures for material picking,design calculation and construction is put forward.
针对工程实践中点支式玻璃屋顶常见的质量问题,从质量控制的各环节分析了产生各种破坏的原因,并从玻璃材料的选用、设计计算、设计与施工应注意事项等方面提出了一些合理的处理措施,以达到消除各类质量问题的目的。
2) point-supported glass curtain wall
点支式玻璃幕墙
1.
Due to its features of open-eyesight and good-perspective,the point-supported glass curtain wall system is popularly applied in public buildings,but it also has the flaw of high energy-consuming.
在公共建筑中广泛应用的点支式玻璃幕墙体系,具有视野开阔、通透美观的优点,但也有能耗过大的缺点。
2.
Point-supported glass curtain wall is a new kind of curtain wall and developing quickly, and it was applied in engineering recently.
点支式玻璃幕墙是近年来开始在玻璃幕墙工程中应用并迅速发展的一种新的幕墙型式。
3.
As a new kind of supporting member,a prestressed fish-shaped cable truss has been widely applied in point-supported glass curtain walls.
预应力鱼腹式索桁架作为点支式玻璃幕墙的支承体系有着广泛的应用,非线性自振特性的研究对于索桁架结构在地震荷载作用下的响应分析具有十分重要的意义。
3) point-supporting glass curtain
点支式玻璃幕墙
1.
Static performance of single-layer cable Mesh point-supporting glass curtain;
单层索网点支式玻璃幕墙的静力性能研究
2.
Study of model-frequency behavior of single-layer orthogonal cable mesh point-supporting glass curtain;
单层正交索网点支式玻璃幕墙自振特性研究
3.
The connection types of supporting point of point-supporting glass curtain often adopt countersunk type or floating-head type.
在本文中,风荷载对点支式玻璃幕墙承载性能的影响,就分别按大挠度和小挠度进行分析和比较,提出了按大、小挠度理论计算的临界风荷载值。
5) plate-glass curtain wall with multiple-supports
点支式玻璃幕墙
1.
Application of the plate-glass curtain wall with multiple-supports in one project in Lishi;
点支式玻璃幕墙在离石某工程中的应用
2.
The designs of a plate-glass curtain wall with multiple-supports are made of the following procedures.
点支式玻璃幕墙的玻璃面板由支承点支承, 支承点通过玻璃上的圆洞与玻璃连结, 有钢爪式等几种连接方法。
6) dot point glass facade
点支式玻璃建筑
1.
Dynamic characteristics of monolayer cable net for dot point glass facade;
点支式玻璃建筑单层索网体系的动力特性
补充资料:闭式单点、双点压力机
| |||||||
主要参数内容 | 国际先进 | 国内先进 | 国内一般 | 国内落后 | 评定方法及说明 | ||
(一)加工精度 | 参照GB10924-89、GB10933-89、JB5200-91 | ||||||
1、滑块下平面对工作台上平面的平行度(mm) | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
0.02+0.10/100×滑块下平面的被测长度 | |||||||
2、滑块行程对工作台上平面的垂直度 | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
0.05+0.02/100×滑块行程长度 | |||||||
(二)结构性能 | |||||||
1、离合器、制动器接通率,当滑块行程次数≤16次/分时为70%,≤25次/分时为60%,≤45次/分时为50% | 大于规定值10% | 大于规定值 | 达到规定值 | 达不到规定值 | |||
2、液压超负荷保险装置、微调装置、吨位指示器 | 全部具有 | 全部具有 | 部分具有 | 没有 | |||
(三)噪声dB(A) | |||||||
1、公称力≤400kN | ≤85 | ≤87 | ≤88 | >88 | |||
2、公称力>400kN | ≤87 | ≤88 | ≤90 | >90 |
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条