1) sequential static parameter adjustment
序贯静态参数平差
1.
The methods of first using parameter eliminating method to simplify the GPS pseudorange observation equations,and then using sequential static parameter adjustment to calculate the position are introduced.
介绍了利用参数消去法对GPS伪距点定位方程进行约化,结合序贯静态参数平差进行了定位解算,提高了单历元的计算精度。
2) sequential adjustment
序贯平差
1.
The formulas of the fixed parameter sequential adjustment are deduced and the characteristics of this method are analysed.
采用简洁的方式，导出了固定参数序贯平差的计算公式，并对ＧＰＳ网与地面网中存在的固定边长和固定坐标方位角等约束条件进行序贯平差。
2.
The sequential Adjustment with Constraints among Parameters is presented briefly in the first,the two arithmetics of the robustment estimation for sequential adjustment with constraints are conducted in detail,and their characteristics are analyzed.
推导了附加约束条件的序贯平差抗差估计解法,对其两种解法进行了分析比较,这两种方法上是一致的。
3) successive adjustment
序贯平差
1.
The principle of detecting gross errors by successive adjustment is given in this paper.
给出了序贯平差探测粗差原理。
4) Robust Sequential Estimation
抗差序贯平差
5) Static adjustment
静态平差
6) static parameter
静态参数
1.
The components and working principle of the integrated measurement system for projectile s static parameters are introduced in this paper.
介绍了用光电传感器、荷重传感器、单片机和PC机组成的一套弹箭静态参数综合测量系统以及该系统的工作原理;分析了测量处理电路原理以及设计使用过程中应注意的问题。
2.
The computer system centring at data collecting card is used a automatic testing system is designed to test the static parameter of angular acceleration gyroscope.
针对角加速度陀螺仪生产装配过程中产品性能测试的需要,根据角加速度陀螺仪的工作原理,推导了其简化的工程应用数学模型,采用以数据采集卡为核心的计算机系统,设计了一种用于角加速度陀螺仪静态参数的自动测试系统。
3.
The composite method was presented according to the problems existed in the Matrah method,which method can only detect the contaminant between the contacts via measuring relay s static parameter.
针对在航天继电器多余物检测中马特拉方法只检测继电器静态参数确定触点之间是否存在多余物微粒的缺点,提出了复合检测法,即在原方法的基础上,扩展了检测继电器的动态参数(如超程时间、动作时间等)。
补充资料：不合格百分率计数检验的序贯抽样方案
不合格百分率计数检验的序贯抽样方案
sequential sampling plans for inspection by attributes for percent nonconforming
加hege比ifen.o Jishu Jianvan dex叩uanC伙泪四叩fa叩’On不合格百分率计数检验的序贯抽样方案(se-quenti吐~plingp】川15 for inspection场attributesforpe二ni nonconfo丽ng)逐个地(或成组地)抽取个体，但事先并不固定它们的个数，根据事先规定的规则，直到可以做出接收或拒收批的决定为止。作为代表性的是IEC 1 123:l卯l标准。 设在n.抽试产品中出现;个不合格，且抽样方案给出:，h两数。判决规则如下:①如;n一h〕r，则接收;②如:n一h
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条