1) lithium salts sintering aids
锂盐烧结助剂
2) Sintering Additives
烧结助剂
1.
Activated sintering and sintering additives for silicon carbide ceramics;
碳化硅陶瓷的活化烧结与烧结助剂
2.
Effects of sintering additives of Co_2O_3 on properties of Ce_(0.8)Gd_(0.2)O_(1.9);
烧结助剂Co_2O_3对Ce_(0.8)Gd_(0.2)O_(1.9)性能的影响
3.
The choice of AlN sintering additives and five sintering technologies were analysed,namely hot pressi.
介绍AlN陶瓷的典型性能和导热机理;讨论AlN粉末的5种合成方法:铝粉直接氮化法、Al2O3碳热还原法、化学气相沉积法、溶胶?凝胶法、自蔓延高温合成法和等离子化学合成法;分析AlN烧结助剂的选择和5种烧结工艺:热压烧结、无压烧结、放电等离子烧结、微波烧结及自蔓延烧结;阐述AlN基板的制备工艺及其影响因素。
3) sintering aid
烧结助剂
1.
Influence of sintering aids on pressureless sintering of Sialon ceramics;
烧结助剂对Sialon常压烧结的影响
2.
Effect of sintering aids on reaction-bonded Si_3N_4-BN composites;
烧结助剂对反应烧结Si_3N_4-BN复合材料的影响
3.
Research progress of low-temperature sintering aids of AlN ceramic
低温烧结氮化铝陶瓷烧结助剂的研究进展
4) sintering aids
烧结助剂
1.
Experiment study on AlN ceramics low-temperature sintering aids;
氮化铝陶瓷低温烧结助剂体系的研究
2.
The influences of sintering aids Al2O3-Y2O3on sintering performance of B4C/B-Al composites were studied in vacuum carbon tube furnace under argon atmosphere at 1 850 ℃ holding 1.
5 h、真空碳管炉氩气保护条件下研究了烧结助剂Al2O3-Y2O3对B4C/B-Al复合材料烧结性能的影响。
3.
Spark plasma sintering(SPS) was applied to prepare α-Si3N4 ceramics of different controlled densities with magnesia,silicon dioxide,alumina as the sintering aids and the relationship between density of samples,the content of sintering aids and dielectric property was explored.
以MgO、Al2O3和SiO2作为烧结助剂,采用放电等离子烧结(SPS)方法制备密度可控的α-Si3N4陶瓷材料。
5) additives
烧结助剂
1.
Effects of sintering additives and process on density and thermal conductivity of BeO ceramic;
烧结助剂和工艺对BeO陶瓷密度和热导率的影响
2.
Silicon nitride ceramics were prepared by hot-press sintering method using α-Si3N4 power with short chopping carbon-fiber as starting materials,Y2O3-La2O3 and LiF-MgO-SiO2 as additives,respectively.
采用Y2O3-La2O3和LiF-MgO-SiO22组烧结助剂,通过短切碳纤维增韧的方法,热压烧结制备了氮化硅陶瓷,并对所得氮化硅陶瓷的相组成、微观结构和力学性能进行了分析和讨论。
3.
The effects of additives to Si3N4 matrix layers on microstructure and properties of laminated Si3N4/BN ceramics were studied.
研究了MgO-Y2O3-Al2O3体系(相应的层状复合陶瓷试样记为A)、Y2O3-Al2O3体系(相应的层状复合陶瓷试样记为B)及La2O3-Y2O3-Al2O3体系(相应的层状复合陶瓷试样记为C)烧结助剂对Si3N4/BN层状复合陶瓷结构与性能的影响。
6) sintering additive
烧结助剂
1.
Using a reticulated polymeric sponge with interconnected pores as primal framework and immersing into Si_3N_4 slip consisting of Al, Al_2O_3 and ZrO_2 as sintering additives, a porous Si_3N_4 ceramics with high porosity and interconnected pores was prepared by twice immersing and sintering process.
选用具有连通气孔的网状聚氨酯海绵作为骨架,利用有机泡沫浸渍的Si3N4浆料工艺,以Al粉、Al2O3和ZrO2作为Si3N4陶瓷材料的烧结助剂,采用2次挂料及2步烧结工艺制备了性能良好的多孔陶瓷骨架。
2.
DTA was used to study the thermostability of the materials,at the s ame time, the further study on the effect of the sintering additives and sinteri ng temperature on the properties of the composite was made.
利用共沉淀法制备了磷酸锆,用差热分析法(DTA)研究了Zr2P2O7的热稳定性情况,并进一步研究了烧结助剂的量、烧结温度等对其性能的影响。
3.
Si3N4/(W,Ti)C was fabricated using Y2O3 and Al2O3 as sintering additives.
Y2O3-Al2O3为复合烧结助剂,以(W,Ti)C为增韧补强材料,制备了Si3N4基复合陶瓷材料。
补充资料：锂盐生产用蒸发器(新疆锂盐厂)
锂盐生产用蒸发器(新疆锂盐厂)
，「·谬 铿盐生产用蒸发器(新疆锉盐厂)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条