1) molten steel level
钢液高度
3) molten steel temperature
钢液温度
1.
By optimizing the technological regulation,importing real-time monitoring,strengthening the management,the molten steel temperature stability can be assured and the breakout rat.
通过优化相关工艺制度,引入实时监控系统,加强管理,可保证连铸钢液温度的稳定性、显著降低漏钢率。
2.
A neural network prediction system of molten steel temperature for VD has been developed.
开发了较完善的 VD炉终点钢液温度在线预报系统 ,应用神经网络方法对 VD炉终点钢液温度进行预报 ,系统在线连续预报了 76炉次 ,预报温度与实际测量温度之差在± 4℃、± 5℃、± 6℃之内的炉次分别占 67。
3.
The prediction model of molten steel temperature for LF VD CC route has been developed by means of meural network method The difference between the predicted and measured temperature was in range of 0 7 ℃ for 85 % heats,and less than 10 ℃ for all heats Because of data replacement function in the model,the prediction precision can be guaranteed regardless of the influence of gradual change factor
利用神经网络方法开发了ＬＦ—ＶＤ—ＣＣ钢液温度预报模型。
4) high strength steel
高强度钢
1.
Development on control of hydrogen in high strength steel weld metal;
高强度钢焊缝金属氢控制研究进展
2.
Analysis about formation and microstructure of laser-welding-tailored-blanks with unequal thickness of high strength steels;
高强度钢差厚板激光拼焊焊缝成形及组织分析
3.
Precipitate Behavior of Second Phase and Structure of Annealed 1.5mm Cold Rolling Sheet of Nb-Ti Microalloy High Strength Steel;
Nb-Ti微合金高强度钢1.5mm冷轧板退火组织和第二相析出行为
5) high-strength steel
高强度钢
1.
Research of accelerated corrosion test method of zinc, cadmium plating on high-strength steel;
高强度钢锌、镉镀层加速腐蚀试验方法研究
2.
The trial qualification by us ing less-matched welding materials to weld high-strength steel;
焊接高强度钢用低匹配焊接材料的试验评定
3.
Effect of processing parameters on strength and toughness of high-strength steel
工艺参数对高强度钢强度及韧性的影响
6) high strength IF steel
高强度IF钢
1.
The relationship of galvannealed temperature,galvannealed time,surface pattern,η,ζ,and δ1 were investigated by testing high strength IF steel with the intensity of 340 MPa.
选取340 MPa高强度IF钢热镀锌钢板作为实验原板,分析了不同镀层退火工艺参数对板带镀层表面的影响,重点研究了镀层退火的温度、保温时间与表面形貌以及η,ζ,1δ各个相的关系。
2.
This paper summarizes research and application of galvanizing on ultra light auto body steel,stressing on galvanizing process and factors affecting properties for bake-hardening steel,high strength IF steel,dual phase steel and transformation induced plasticity steel.
综述了超轻汽车车体用钢热镀锌的研究及应用现状,重点介绍了烘烤硬化钢、高强度IF钢、双相钢、相变诱导塑性钢等热镀锌的生产工艺和性能影响因素。
3.
Compared with traditional high strength IF steel,the recrystallization behavior during annealing process of a high C-Nb high strength IF steel was studied by using a Gleeble-1500 simulator.
以传统高强度IF钢为对比,用Gleeble-1500热模拟机研究了440MPa级高C-高NbIF钢的再结晶行为,采用盐浴退火方法研究了退火温度对该钢显微组织和力学性能的影响。
补充资料：降液管清液层高度
分子式：
CAS号：
性质：又称降液管清液层高度。板式塔降液管内的液柱液面到下层塔板的垂直距离。如图中的Hd（图暂缺）。为保持板式塔正常操作，避免发生液泛，降液管液柱高度不能超过一定限度。一般应满足Hd≤(0.4～0.6)(HT+hw)，式中HT为塔板间距，hw为堰高，系数一般取0.5，易起泡物系取0.4，不易起泡物系取0.6。
CAS号：
性质：又称降液管清液层高度。板式塔降液管内的液柱液面到下层塔板的垂直距离。如图中的Hd（图暂缺）。为保持板式塔正常操作，避免发生液泛，降液管液柱高度不能超过一定限度。一般应满足Hd≤(0.4～0.6)(HT+hw)，式中HT为塔板间距，hw为堰高，系数一般取0.5，易起泡物系取0.4，不易起泡物系取0.6。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条