1) eccentric sucking mud
偏心吸浆
3) Off-center
[英]['ɔ:f'sentə] [美]['ɔf'sɛntɚ]
偏心
1.
Two methods about how to calculate the bearing off-center of curved beam bridge are presented,which is common but no conclusion now.
根据恒载条件下横桥向双支座反力相等原则,对曲线梁桥设计中常见但尚无定论的支座偏心问题提出了2种计算方法,即最小偏心法和一致偏心法。
4) eccentric
[英][ɪk'sentrɪk] [美][ɪk'sɛntrɪk]
偏心
1.
Topography guided LASIK on correction of eccentric ablation;
角膜地形图引导准分子激光一次性矫治角膜切削偏心
2.
A Convenient Design Method for Eccentric Bridge Pier and Abutment;
一种简便的偏心墩台设计方法
3.
The real time detector method of multi-cable eccentric degree;
多线芯电缆偏心度的在线检测
5) offset
[英]['ɔfset] [美]['ɔf'sɛt]
偏心
1.
Process parameter's influence on thickness of first neck-section in offset forward spinning;
偏心正旋工艺参数对起旋端壁厚影响规律研究
2.
A CFD software,Star-CD,was used to simulate the effect of transferring the injection nozzle location from the combustion chamber center to the cylinder center in a diesel engine with helical inlet port and offset ω combustion chamber.
使用CFD软件Star-CD对具有偏心ω燃烧室柴油机的两种不同喷嘴位置的燃烧过程进行数值模拟,一种是接近于燃烧室的正上方,另一种是位于气缸的中心位置。
3.
Numerical simulations are processed on decoupled explosion while the explosion is offset from the center of spherical cavity.
对球形空腔偏心解耦爆炸进行了数值模拟,得到了不同方向和不同爆心距节点的S波和P波速度曲线以及岩石单元中拉伸应力的传播过程。
6) eccentricity
[英][,eksen'trɪsəti] [美]['ɛksɛn'trɪsətɪ]
偏心
1.
Detection and control of eccentricity in a cold mill based on stochastic approximation method;
随机逼近法对轧辊偏心信号的检测与控制
2.
Research on eccentricity of mould for the twin-tub of double-tube washing machine;
双桶洗衣机连体桶模具偏心问题研究
3.
Effect of eccentricity between output shaft of dynamic balancing machine and the parts to be tested on dynamic balancing result;
动平衡机输出轴与试验部件之间偏心量对动平衡试验的影响
补充资料：在AutoCAD中偏心圆锥与偏心圆台实体的画法
现在要画一个偏心圆锥,底面在WCS的XY平面上,圆心(0,0,0),半径100,顶点(300,0,400)在ZX平面上.
1)连接PA,PB. A(-100,0,0) B(100,0,0)
图1
在当前坐标下:
2)延长PA到C,使PA=CA;延长PB到D,使PB=DB;
3)连接CD;
4)以CD为直径画圆;
5)用XLINE命令中的二等分选项作角CPD的角平分线PO,交CD于O;
6)过O作CD的垂线,交圆于E,F;
图2
7)用三点UCS命令,取三点为:O,P,C;
8)过点O作PO的垂线GO,交PC于G;
图3
9)再次用三点UCS命令,取三点为O,F,G;
10)现在就可以画椭圆锥了!
cone-e-c-捕捉O点-捕捉F点-捕捉G点-a-捕捉P点;
图4
11)回到WCS,剖切椭圆锥
SL-选择椭圆锥-回车-XY-回车-捕捉P点.
12)删除辅助线条.
图5
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条