1) poly(phthalazine ether sulfone ketone)coated fiber
聚醚砜酮涂层纤维
1.
Analysis of phenolic compounds in aqueous samples by gas chromatography coupled with headspace solid-phase microextraction using poly(phthalazine ether sulfone ketone)coated fiber;
聚醚砜酮涂层纤维顶空固相微萃取-气相色谱法分析水中痕量的酚类化合物
2) polyether sulfone fiber
聚醚砜纤维
1.
High temperature-pressure dyeing of polyether sulfone fiber;
聚醚砜纤维高温高压染色性能
3) PEK fiber
聚醚酮纤维
4) PPESK
聚醚砜酮
1.
Mechanical properties of continuous carbon fiber reinforced PPESK blends composites;
连续炭纤维增强杂萘联苯聚醚砜酮共混树脂基复合材料力学性能
2.
Preparation of PPESK based composite carbon membrane for gas separation
聚醚砜酮基炭膜的制备及其气体分离性能
3.
Nanometer and micrometer ZrO2 particle-filled poly (phthalazine ether sulfone ketone) (PPESK) composites with various filler volume fractions were prepared by heating compression molding.
采用热压成型的方法制备了纳米、微米ZrO2填充聚醚砜酮(PPESK)复合材料;考察了复合材料的显微硬度和弯曲强度;并研究了干摩擦条件下纳米、微米ZrO2颗粒对复合材料摩擦磨损性能的影响;利用扫描电子显微镜(SEM)观察分析ZrO2/PPESK复合材料磨损表面形貌及磨损机理。
5) poly(phthalazine ether sulfone ketone)
聚醚砜酮
1.
Structure and performance of PEG-acrylate immobilized porous poly(phthalazine ether sulfone ketone) membrane;
聚乙二醇丙烯酸酯表面改性聚醚砜酮微孔膜的结构和性能
2.
The dry sliding friction and wear properties of nanometer TiO 2 particle filled poly(phthalazine ether sulfone ketone) (PPESK) composites were investigated with an MM 2000 tester by sliding PPESK based composites against plain carbon steel(AISI1045) ring, with an emphasis on exploring the effect of the filler content and applied loads on the tribological behaviors of the composites.
采用热压成型的方法制备了纳米 Ti O2 填充聚醚砜酮 (PPESK)复合材料 ,在 MM- 2 0 0 0摩擦磨损试验机上考察了干摩擦条件下纳米 Ti O2 含量以及试验载荷对复合材料摩擦磨损性能的影响 ,并利用扫描电子显微镜 (SEM)观察分析 PPESK及纳米 Ti O2 / PPESK复合材料磨损表面形貌及磨损机理。
6) PPESUK
聚醚砜酮
1.
INFLUENCES OF THE LOAD, VELOCITY AND TEMPERATURE ON THE FRICTION AND WEAR PROPERTIES OF PPESUK;
载荷、速度及环境温度对聚醚砜酮摩擦磨损性能的影响
2.
Nanometer and micrometer ZnO particle-filled PPESUK composites with various filler volume fractions were prepared by heating compression molding.
用热压成型法制备了纳米、微米ZnO填充联苯型聚醚砜酮(PPESUK)复合材料;考察了复合材料的显微硬度和弯曲强度;并研究了干摩擦条件下纳米、微米ZnO对复合材料摩擦磨损性能的影响。
补充资料：涂层纤维
分子式：
CAS号：
性质：用某种物质涂覆于纤维表面，以改善其特性的复合纤维。例如塑料光导纤维是在聚甲基丙烯酸甲酯芯纤维的表层涂上氟树脂，使纤维的光损耗、耐磨、挠曲、难熔等性能得到改善。而所谓“银丝”是以涤纶薄膜为原料，采用真空蒸镀技术，将铝蒸镀在薄膜上。如生产“金丝”则在薄膜表面再涂上黄色颜料的树脂。
CAS号：
性质：用某种物质涂覆于纤维表面，以改善其特性的复合纤维。例如塑料光导纤维是在聚甲基丙烯酸甲酯芯纤维的表层涂上氟树脂，使纤维的光损耗、耐磨、挠曲、难熔等性能得到改善。而所谓“银丝”是以涤纶薄膜为原料，采用真空蒸镀技术，将铝蒸镀在薄膜上。如生产“金丝”则在薄膜表面再涂上黄色颜料的树脂。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条