说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 剪切保留率
1)  shear retention rate
剪切保留率
1.
Effect of ion on viscosity shear retention rate of associating polymer solution;
离子对缔合聚合物溶液黏度剪切保留率影响研究
2)  shear rest
剪切停留
1.
Influence of shear rest on microstructure of partially remelted A356 alloy and its transient rheological behavior;
剪切停留对液固温区A356合金组织及瞬态流变行为的影响
2.
The influence of shear rest on the microstructure variation and the transient rheological behavior of semi solid A356 alloy with different morphologies of the primary alloy α phases was explored by conducting rest time experiments with a self designed rheometer.
采用自行研制的流变装置进行瞬态流变试验 ,研究了剪切停留对液固温区 A35 6合金初生 α相聚合重构过程及其瞬态流变行为的影响。
3)  constant shear stress
恒剪切率
4)  shear rate
剪切速率
1.
Study on relationship of viscosity and shear rate of potato starch size;
马铃薯淀粉浆料的粘度与剪切速率关系的研究
2.
Experimental investigation of the apparent viscosity and the shear rate of gelled propellant in straight round pipe;
凝胶推进剂直圆管中剪切速率与表观粘性实验研究
3.
Impact of shear rate on microstructure of PA 6/PP blends
剪切速率对PA 6/PP共混物微观结构的影响
5)  shear rate
剪切率
1.
Calculation of Average Shear Rate of Power-law Fluid for Annular Pipe Flow;
幂律流体环空管流平均剪切率的计算
2.
Estimation of average shear rate in stirred vessels for pipelining shear simulation;
管输剪切模拟搅拌槽中流体平均剪切率的计算
3.
An estimation approach to the shear rate of the power law fluid in turbulent pipe flow;
幂律流体在圆管内湍流流动剪切率的近似计算
6)  shearing rate
剪切速率
1.
The experimental results show that the apparent viscosity of semi-solid A356 alloy increases with increasing the fraction solid, but decreases with increasing the shearing rate in the steady-state.
结果表明:半固态A356合金的稳态表观粘度(η_a)随着固相分数(f_s)的增加而增加,但随剪切速率(γ)的增大而减小,当f_s达到某一临界值之后,η_a迅速增加,可用方程η_a=2。
2.
The influence of molecular weight, shearing rate and temperature on the rheologic behavior of domestically manufacturing linear PPS (i.
以国产线性聚苯硫醚树脂为原料,研究了分子质量、剪切速率、温度对PPS树脂流变行为的影响。
3.
The diameter, flow, shearing rate ,draw ratio and pressure difference were calculated.
讨论了"┃·"异形喷丝板的设计、纺丝工艺及后加工工艺,计算出喷丝板毛细孔的当量直径、单孔流量、剪切速率、喷丝头拉伸比,验证了喷丝孔的结构参数是影响可纺性的关键因素。
补充资料:电导率(见电阻率)


电导率(见电阻率)
conductivity

d!日nd日O}已电导率(eonduetivity)见电阻率。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条