1) bis transition point
双拐点
1.
The experimental results showed that there occurred bis transition points or pseudo double plateau regions on the γ -lg c curves of AS-PVP and of AS-PEG with greater molecular weights.
实验结果表明 ,AS与PVP以及与相对分子质量较大的PEG间混合体系的γ -lgc曲线均具有双拐点的特点 ,为拟双平台型曲线。
2) inflection point
拐点
1.
The Algorithm and application of discrete inflection point;
离散型函数拐点算法及应用
2.
8 A note on extreme points and inflection points of rational entire functions;
有理整函数的极值点和拐点的一个注记
3) turning point
拐点
1.
2007:the profit turning point for papermaking industry;
2007:造纸业迎来盈利拐点?
2.
The general trend of work safety in China have entered the turning point——macro-early warning and analysis of trend of work safety
中国安全生产大趋势已进入拐点——生产安全事故宏观预警与发展态势分析
3.
Does Turning Point of Real Estate Price Emerge with Macro-Control
宏观调控下房地产价格拐点会出现吗
4) inflexion
[英][in'flekʃən] [美][ɪn'flɛkʃən]
拐点
1.
Analyzing and Forecasting on the Emergence Time of China s Secondary Industry Inflexion;
中国第二产业拐点出现时刻分析与预测
2.
An Inflexion Explanation for"Preference for Boys"from Social Gender Culture Perspective
“男孩偏好”社会性别文化“拐点”解析
5) inflexion point
拐点
1.
Discussion on the effect of changing mathematic simulation curve inflexion points to the polymerization temperature rising state;
浅析数学模拟曲线拐点变化对聚合升温反应状态的影响
2.
Moreover,the flocculation settlement curves of the lignin locution were determined at deferent temperatures under the condition of the polyaluminum ferric chloride flocculation,the sense of the inflexion point of the curve was discussed,and the acaivation energy of the colloid solution flocculatiov was eltimated,which corresponds to the potential-energy(Φm) between sol particles accordin.
用传统的化学动力学方法讨论了温度对絮凝过程的影响,测定了木质素溶液在不同温度时被聚氯化铝铁(PAFC)絮凝的絮凝沉降曲线,讨论了曲线上拐点的意义,并估算出该胶体溶液絮凝时的活化能,它相当于DLVO理论为胶体粒子间的势能能垒φm,实验得出φm≈16。
3.
Several sufficient conditions of inflexion point of curve are gained.
给出了曲线拐点判定的几个充分条件,对比曲线的拐点和极值的判别方法,研究了曲线的拐点、极值点和不可导点之间的关系。
6) inflection points
拐点
1.
We analyze the geometric features like cusps and inflection points in the curve and calculate the cusps and inflection points, then give a necessary and sufficient condition to the inflection points.
本文是在文 [1 ]基础上的继续和发展 ,主要对有理 H-样条曲线的形状进行分析 ,讨论其诸如拐点和奇点的几何特征 ,给出有理参数平面三次 H-样条曲线在非退化情况下有拐点的充要条件 ,并证明在区间 ( 0 ,1 )内曲线段无奇点的结论。
2.
In this paper the authors analyze the shape features like singularities,inflection points and local or global convexity of rational C-Bézier curve,then give the necessary and sufficient conditions for this curve having one or two inflection points,or a loop,or a cusp,or being local or global convex in terms of the relative position of its control polygons′ side vectors.
对有理C-Bézier曲线进行了形状分析,得出曲线上含有奇点、拐点和曲线为局部凸或全局凸的、用控制多边形边向量相对位置表示的充分必要条件,并讨论了权因子变化对曲线形状图的影响。
3.
In this paper we discuss the distribution of singular points and inflection points on a planar C-Bezier curve in details, and give the necessary and sufficient conditions for having one or two inflection points, or a loop, or a cusp, or none of the above points on the curve in terms of their control polygons.
本文完全地讨论了平面C-曲线和平面C-Bezier曲线的奇拐点和凸性性质:曲线段为且必为下列情形之一:有一各拐点,两个拐点,一个尖点,一个二重结点,处处为凸;并给出了相应的用控制多边形相对位置表示的充分必要条件。
补充资料:闭式单点、双点压力机
| |||||||
主要参数内容 | 国际先进 | 国内先进 | 国内一般 | 国内落后 | 评定方法及说明 | ||
(一)加工精度 | 参照GB10924-89、GB10933-89、JB5200-91 | ||||||
1、滑块下平面对工作台上平面的平行度(mm) | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
0.02+0.10/100×滑块下平面的被测长度 | |||||||
2、滑块行程对工作台上平面的垂直度 | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
0.05+0.02/100×滑块行程长度 | |||||||
(二)结构性能 | |||||||
1、离合器、制动器接通率,当滑块行程次数≤16次/分时为70%,≤25次/分时为60%,≤45次/分时为50% | 大于规定值10% | 大于规定值 | 达到规定值 | 达不到规定值 | |||
2、液压超负荷保险装置、微调装置、吨位指示器 | 全部具有 | 全部具有 | 部分具有 | 没有 | |||
(三)噪声dB(A) | |||||||
1、公称力≤400kN | ≤85 | ≤87 | ≤88 | >88 | |||
2、公称力>400kN | ≤87 | ≤88 | ≤90 | >90 |
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条