1) Ag-Zn alloy
Ag-Zn合金
1.
Porous silver materials have been fabricated by dealloying of Ag-Zn alloys in H2SO4 solution.
本文利用Ag-Zn合金在H2SO4溶液中去合金化法制备多孔银,采用X射线衍射分析、扫描电镜、EDS能谱分析等手段,研究了Ag23。
2) Ag-Cu-Zn alloy
Ag-Cu-Zn合金
1.
Adding Cr/Ti metal powder to improve brazing performance of Ag-Cu-Zn alloy to diamond;
Cr、Ti金属粉改善Ag-Cu-Zn合金对金刚石的钎焊性能研究
2.
Cr powder was added between Ag-Cu-Zn alloy and diamond grits to braze diamond on the steel substrate by means of high frequency induction heater.
在Ag-Cu-Zn合金钎料中添加Cr粉,将混合钎料用于钢基体上的金刚石高频感应钎焊。
3.
By appropriate process parameters,the Ag-Cu-Zn alloy ingot with good surface quality and even unidirectional microstructure was fabricated on the self-designed horizontal heated mould continuous casting apparatus.
在自制的水平式热型连铸设备上,选用合适的工艺参数制备出了表面质量良好、内部组织沿轴向均匀分布的Ag-Cu-Zn合金铸棒。
3) Pd-Ag-Sn-In-Zn alloy
Pd-Ag-Sn-In-Zn合金
1.
Age-hardening behaviour and the related microstructural changes were studied to elucidate the hardening mechanism of Pd-Ag-Sn-In-Zn alloy by means of hardness test,XRD,SEM.
通过硬度测试、X射线衍射(XRD)分析、扫描电镜(SEM)观察研究了Pd-Ag-Sn-In-Zn合金时效强化行为及相关的微观结构变化,从而很好地解释了该合金的时效强化机制。
4) Al-Ag alloy
Al-Ag合金
1.
The kinetic Monte Carlo method based on the Multi-States Ising Model,was applied to simulate the effect of microelements on the microstructural evolution of Al-Ag alloys during initial aging stage.
采用基于Multi-States Ising Model的Kinetic Monte Carlo算法,模拟研究了添加微量元素对Al-Ag合金时效初期微观结构的演变过程的影响。
2.
Taking into account the influence on the lattice constant from temperature,the valence electronic structures of GP zones of η-form in the Al-Ag alloy,and the interfacial energy between GP zones of η-form and matrix were calculated by using empirical electron theory in solid and molecules(EET) and the extension of Becker model.
考虑温度对晶格常数的影响,运用固体与分子经验电子理论,对Al-Ag合金的η型GP区的价电子结构进行计算;在此基础上,运用Becker推广模型,对该体系的η型GP区与基体之间的界面能进行预测。
3.
The valence electron structure of GP zone ? phase in Al-Ag alloy was calculated according to the “empirical electronic theory in solid”(EET), and the interface energy based on the information of the valence electron structure was calculated also.
运用固体经验电子理论,对Al-Ag合金GP区?相的价电子结构进行计算,并且在此基础上计算了GP区和基体的界面能。
5) Ag-C alloy
Ag-C合金
6) Cu-Ag alloy
Cu-Ag合金
1.
Strain strengthening of Cu-Ag alloy in situ filamentary composites;
Cu-Ag合金原位纤维复合材料的应变强化效应
2.
Effects of annealing and cold-working on properties of continually-unidirectionally solidified Cu-Ag alloy;
热处理和冷变形对连续定向凝固Cu-Ag合金性能的影响
3.
The Cu-Ag alloy in situ filamentary composites with different Ag contents were prepared.
制备了具有不同Ag含量的Cu-Ag合金及其原位纤维复合材料,增加Ag含量可以细化铸态组织和Ag纤维尺寸,增大合金的极限拉伸强度和电阻率。
补充资料：东北轻合金加工厂生产的铝合金挤压管材和空心材
东北轻合金加工厂生产的铝合金挤压管材和空心材
睽铝合;;:;;;、:;产的
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条