1) carbonaceous schist-host ores
碳质片岩型矿体
2) Xitieshan carbonaceous schist type Pb-Zn deposit
(碳质)片岩型矿床
1.
In summary,the formationgenesis of sulfide and siliceous rockcherts of the Xitieshan carbonaceous schist type Pb-Zn deposit are typically related toof volcanic-exhalative-sedimentation(SEDEX),the ore-forming matters materials mainly come from volcanic rocks and deep crust.
锡铁山(碳质)片岩型矿床具典型的"双层结构",笔者对层状矿体中硫化物、硅质岩及其围岩火山岩稀土元素分析表明,硫化物∑REE较低,在4。
3) carbonaceous mylonite schist
碳质糜棱片岩
1.
Located on the northern margin of Qaidam massif,the Tanjianshan gold deposit occurs in the carbonaceous mylonite schist of Wandonggou Group of Mesoproterozoic Jixian System as well as in the Late Variscan intrusive rocks.
滩间山金矿床产于中元古界万洞沟群碳质糜棱片岩和华力西晚期侵入岩中。
2.
Tanjianshan gold deposit is situated in the northern margin of Qaidam Massifand occurs in the Middle Proterozoic Wandonggou group carbonaceous mylonite schist andLate Variscan intrusive rocks.
滩间山金矿床位于柴达木地块北缘,产于中元古界万洞沟群碳质糜棱片岩和华力西晚期侵入岩中。
4) carbonaceous-siliceous-argillitic rock type uranium deposit
碳硅泥岩型铀矿
1.
This paper describes metallogenic characteristics,and the formation mechanism of those carbonaceous-siliceous-argillitic rock type uranium deposits occurring at the margin and in the basement of red basins,and proposes that there must be certain direct genetic relation between red basins and the formation of uranium deposits.
碳硅泥岩型铀矿床主要产于中新生代沉积盆地 (简称为红盆 )的附近。
5) altered granite-type tungsten deposit
岩体型钨矿
1.
Isotope chronological evidence for Upper Jurassic petrogenesis and mineralization of altered granite-type tungsten deposits in the Zhangtiantang area,southern Jiangxi;
赣南张天堂地区岩体型钨矿晚侏罗世成岩成矿的同位素年代学证据
6) porphyry copper body
斑岩型矿体
补充资料：铝碳质整体塞棒
铝碳质整体塞棒
alumina graphite monolithic stopper
IUtanzhi zhengti sa}bdng铝碳质整体塞棒(alumina graphite monoli-thicst叩per)以刚玉和鳞片状石姜为主要原料烧成的控制钢液流量的耐火制品。其特点是整体性好，代替了由传统的袖砖和塞头组装的塞棒，使用更安全，而且还可以通过塞棒向中间罐水口吹氢，净化钢水，防止水口堵塞。 铝碳质整体塞棒的理化指标:A120360%，F·C25%，体积密度2.359/c m3，显气孔率13%，耐压强度14.7MPa，抗折强度(1400℃)5.oMPa，线膨胀率(1000℃)。.5%。其制造工艺是将刚玉、石墨和添加剂等原料按配比称量，以酚醛树脂为结合剂，经混练，用等静压机成型。半成品经干燥后，在无氧化烧成窑内烧成。最后，经X射线无损探伤、车床加工、喷涂防氧化涂层等工序，经检验合格后为成品。铝碳质整体塞棒的工艺流程见图。 刚玉石墨添加剂福猛啮~遍州画画趣画莎甲’ 成品 铝碳质整体塞棒的生产工艺流程 在制造中，配料要准确，原料要符合工艺要求，泥料必须造粒，成型压力为120~150MPa，烧成温度为1000~1350℃。 该制品安装于连铸机中间罐内，用其开启程度来控制钢水流量的大小.要求干燥贮存，使用前必须预热。 (周川生)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条