1) name
[英][neɪm] [美][nem]
名义
1.
In order to clarify the relations between New Yuefu and Yue Baishi , it is necessary to define its name first.
为厘清新乐府与元白诗派的成立之间的关系,有必要先对其名义作一界定。
2) nominal strength
名义强度
1.
The research progeny about corrosion character and deterioration mechanism of mechanical property of the corroded steel bars in concrete are mainly summarized and discussed in this article,which also expounds the deteriorating regularity of nominal strength and ductility of the corroded steel bars .
本文主要总结与讨论了混凝土内锈蚀钢筋的锈蚀特征、力学性能退化机理等方面的研究成果,阐述了钢筋锈蚀后其名义强度与延性的退化规律,为研究和评估锈蚀钢筋的力学性能提供了依据。
3) nominal common difference
名义公差
1.
Through the dynamics analysis on the relationship between wheel and rail surface,based on the experimental data from scientific research institutes,we find the effective measure to avoid suspension derailment of empty trains that is to reduce the gap between rail and wheel in straight section(nominal common difference).
通过对车辆车轮与轨面间的动力学原理分析,结合科研部门的大量试验数据,提出减小直线段轮轨间隙(名义公差)是防止空车悬浮脱轨的有效方法。
4) nominal stress
名义应力
1.
Study of fatigue strength assessment methods of welded structures based on nominal stress;
基于名义应力的焊接结构疲劳强度评定方法研究
2.
The fatigue strength of duplex stainless steel welded jointing with longitudinal fillet welded gusset and with longitudinal flat side gusset welded on plate were evaluated by hot spot stress,and the hot spot stress S-N curves were obtained and compared with the nominal stress S-N curves.
针对双相不锈钢焊接结构的疲劳性能问题,通过试验对双相不锈钢纵向角接板焊接接头和侧面角接板焊接接头疲劳强度用热点应力进行了评定,做出了热点应力S N曲线并与名义应力疲劳评定进行了比较。
5) Nominal Strain
名义应变
1.
FE calculations are carried out on a plate with a surface crack,and calculation results illustrate that a same simple proportional relationship exists between the ratio of the crack mouth opening displacement (CMOD) to the nominal strain,△u/ε, and the crack depth, D.
文章利用有限元法,对带有表面半椭圆型裂纹的平板结构进行计算,得到表面裂纹开口位移和名义应变的比值Δu/ε,与表面裂纹深度D,之间同样具有简单的比例系数关系。
6) nominal thickness
名义厚度
1.
The necessity of marking minimum thickness and nominal thickness is analyzed.
针对GB 150中关于成形封头最小厚度的规定进行了探讨,分析了在设计图样中标注封头名义厚度和最小厚度的必要性。
2.
thickness of the formed head shall not be less than the value derived from that head nominal thickness deduct plate thickness minus deviation C1.
GB150-1998《钢制压力容器》和JB/T4746-2002《钢制压力容器用封头》规定:对于按规则设计的封头,成形封头实测的最小厚度不得小于封头名义厚度减去钢板厚度负偏差C1,因为封头名义厚度包含设计者按钢板规格向上圆整值,将造成封头人为增厚。
补充资料：名义
【名义】
（术语）名者体上之名称，义者体上之义理。如言诸行无常，诸行为名，无常为义。又呼召之名目，谓之名，为名所显之法体谓之义，依此义则名义者，与所谓名体或名法同。然就其名与义言之，有名即于义者，有不即者，名即于义，如呼火而出热，诸佛之名号及陀罗尼是也，此云真言。名不即于义，如火之名无热之用，世间一切之名字是也，此云假名。智度论二十五曰：“问曰：义之与名为合耶为离耶？若合名，说火时应烧口。若离，说火时水应来。答曰：亦不合，亦不离。古人假为立名，以名诸法。后人因此名字识是事，如是各各有名字。”肇论曰：“名无得物之功，物无当名之实。”
（术语）名者体上之名称，义者体上之义理。如言诸行无常，诸行为名，无常为义。又呼召之名目，谓之名，为名所显之法体谓之义，依此义则名义者，与所谓名体或名法同。然就其名与义言之，有名即于义者，有不即者，名即于义，如呼火而出热，诸佛之名号及陀罗尼是也，此云真言。名不即于义，如火之名无热之用，世间一切之名字是也，此云假名。智度论二十五曰：“问曰：义之与名为合耶为离耶？若合名，说火时应烧口。若离，说火时水应来。答曰：亦不合，亦不离。古人假为立名，以名诸法。后人因此名字识是事，如是各各有名字。”肇论曰：“名无得物之功，物无当名之实。”
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条