您的位置：首页 -> 词典 -> 口形

1) mouth shape 点击朗读

口形

2) groove type 点击朗读

坡口形式

It is the key to ensure the quality of the weld that adopted reasonable groove type according as the chemical compositions of the approachable side of clad steel plate.

试验结果表明,复合钢板焊接时,可接近的侧面和钢板厚度将决定焊接顺序和焊接材料的选用,而根据可接近侧面材质设计合理的坡口形式,是保证复合钢板焊接质量的关键。

On account of the effect of the rate of dilution on the quality of welded joint of dissimilar steels, the relationship among the rate of dilution, groove type and welding technology was examined and analyzed.

异种钢焊接的稀释率对焊接质量有影响,通过焊缝的稀释率与接头坡口形式、焊接工艺关系试验与分析,采用试验推荐的坡口形式及焊接参数可将焊缝稀释率控制在所要求的范围内。

3) feeding head shape of die 点击朗读

口模形状

例句>>

4) to emit with the form 点击朗读

随形冒口

5) fan-shaped gate 点击朗读

扇形浇口

A fan-shaped gate was used for feeing in the injection mold with two cavities for kitchenware fitting,enhancing uniformity of material feeding and reducing internal stress of the plastic parts.

在一模二腔的厨具塑料配件注塑模结构中,采用扇形浇口进料,提高了进料的均匀性并降低了塑件的内应力。

6) SEN shape 点击朗读

水口形状

The causes of breakout during the production of low carbon steel for cold rolling by Tanggang FTSC thin slab caster were analysed and the optimization countermeasures such as the control of mould taper,the copper plate shape of mould narrow side and SEN shape were put forward.

分析了唐钢FTSC薄板坯连铸机生产低碳冷轧用钢过程中漏钢的成因;提出了优化锥度控制、改进结晶器窄面铜板形状和优化水口形状等技术措施。

补充资料：口形六态

口形六态

口形六态　　诊断学术语。指以口部外形的六种变化，作为辨证的参考。即张（口开不闭），主病虚；噤（口闭不开），主病实；僻（左右斜，口角缓急），主肝经风痰；撮（上下唇紧聚），主邪正交争，正虚邪盛；振（寒栗鼓急，上下振摇），主阳气虚；动（开合频繁），主胃气将绝。

说明：补充资料仅用于学习参考，请勿用于其它任何用途。

参考词条

缩口成形 I形坡口

断口形貌断口形态锥形口罩开口变形缺口形状环形冒口

说明：双击或选中下面任意单词，将显示该词的音标、读音、翻译等；选中中文或多个词，将显示翻译。
	您的位置：首页 -> 词典 -> 口形 1) mouth shape 口形例句>> 2) groove type 坡口形式 1. It is the key to ensure the quality of the weld that adopted reasonable groove type according as the chemical compositions of the approachable side of clad steel plate. 试验结果表明,复合钢板焊接时,可接近的侧面和钢板厚度将决定焊接顺序和焊接材料的选用,而根据可接近侧面材质设计合理的坡口形式,是保证复合钢板焊接质量的关键。 2. On account of the effect of the rate of dilution on the quality of welded joint of dissimilar steels, the relationship among the rate of dilution, groove type and welding technology was examined and analyzed. 异种钢焊接的稀释率对焊接质量有影响,通过焊缝的稀释率与接头坡口形式、焊接工艺关系试验与分析,采用试验推荐的坡口形式及焊接参数可将焊缝稀释率控制在所要求的范围内。 3) feeding head shape of die 口模形状例句>> 4) to emit with the form 随形冒口 5) fan-shaped gate 扇形浇口 1. A fan-shaped gate was used for feeing in the injection mold with two cavities for kitchenware fitting,enhancing uniformity of material feeding and reducing internal stress of the plastic parts. 在一模二腔的厨具塑料配件注塑模结构中,采用扇形浇口进料,提高了进料的均匀性并降低了塑件的内应力。 6) SEN shape 水口形状 1. The causes of breakout during the production of low carbon steel for cold rolling by Tanggang FTSC thin slab caster were analysed and the optimization countermeasures such as the control of mould taper,the copper plate shape of mould narrow side and SEN shape were put forward. 分析了唐钢FTSC薄板坯连铸机生产低碳冷轧用钢过程中漏钢的成因;提出了优化锥度控制、改进结晶器窄面铜板形状和优化水口形状等技术措施。补充资料：口形六态口形六态口形六态　　诊断学术语。指以口部外形的六种变化，作为辨证的参考。即张（口开不闭），主病虚；噤（口闭不开），主病实；僻（左右斜，口角缓急），主肝经风痰；撮（上下唇紧聚），主邪正交争，正虚邪盛；振（寒栗鼓急，上下振摇），主阳气虚；动（开合频繁），主胃气将绝。说明：补充资料仅用于学习参考，请勿用于其它任何用途。参考词条缩口成形 I形坡口

©2011 dictall.com