1) programmed calculation
计算机编程计算
2) computer programming
计算机编程
1.
This paper presents a method to differentiate the closing link with respect to the component links in a plane dimension chain distinguishedHaving determined the increasing link or the decreasing link of the component link,it is convenient to solve the dimension chainThis method is very suited to computer programming,and a practical example is give
在确定组成环的增减性后 ,此法能方便地求解尺寸链 ,非常适合于计算机编程求解 ,并给出了算
2.
To conduct regular evaluations such as financial, technical program risk analysis, value engineering, and other aspects of computing in process of project management are more complicated calculation, and the computer programming needs specialized language environment.
通过在最大众化的Word环境下编制财务评价计算机程序的示例为广大项目管理工作者介绍了简单、方便的计算机编程方法,而这些方法就镶嵌在大家几乎每天都使用的Word中,深入挖掘Word的强大功能无疑会对项目管理技术的发展有极大的帮助。
3.
Therefore,based on the analysis of the relationship between cross section width and cross section height and total cost,the two-dimension golden section method and computer programming methods are introduced to solve the problem by the author.
在对抗滑桩截面宽度和截面高度与抗滑桩费用之间的关系进行综合讨论分析的基础上,引入二维黄金分割法与计算机编程方法,编制了专门的计算软件对抗滑桩截面进行优化设计,以实现满足抗滑要求的前提下使单抗滑桩工程总费用达到最低的优化目的。
3) computer programming;computer software.
计算机编程;计算机软件
4) calculation and programming
计算编程
5) programming calculation
编程计算
1.
The portable computer CASIQFX-4800P was applied to programming calculation in order to calculate coordinate.
利用便携式CA S IQFX-4800P计算机进行编程计算得到桩的坐标。
2.
By combining the formula of Simpson with the programming calculation of CASIOfx-4800P computer, the paper calculates the coordinates of center-line points and boundary-line points of roads, and then lays out the point sites of center-line points and boundary-line points of roads with the help of the electronic total station.
线路中桩、边桩坐标的计算方法有多种,本文从复化辛甫生公式出发,结合CASIOfx-4800P计算器的编程计算,方便快捷地计算出线路中桩、边桩坐标,再用全站仪放样点位坐标,实践证明该方法方便、快捷。
6) computer aided programming
计算机辅助编程
1.
The application of manual programming and computer aided programming in NC machining;
手工编程和计算机辅助编程在数控加工中的应用
2.
This paper introduces the means of spatial arc cam NC maching,the composition of NC system and the method of computer aided programming,and gives the simulation display results of.
介绍了空间弧面凸轮数控加工的方法和数控加工程序的计算机辅助编程方法 ,并给出了辅助编程后模拟显示结
补充资料：计算机输入/输出控制系统(见计算机输入/输出系统)
计算机输入/输出控制系统(见计算机输入/输出系统)
computer input/output control system
iisuanii shuru/shuehu kongzhi xitong计算机输入/输出控制系统(com-puter inPut/ou中ut eontrol system)见计算机输入/输出系统。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条