1) Beijing Tianjin Tangshan region
深部挤压带
1.
The axis of the deep compression zone in the Beijing Tianjin Tangshan region is oriented in a SE NW direction along the line of Ningbo Changping.
京津唐地区的深部挤压带轴线沿宁河、香河、昌平一线呈南东—北西走向，在通过该带的北东向Ｍ和Ｃ面上均有一向北西弯曲的弧形。
2) deep mining above aquifer
深部带压开采
3) deep extrusion
深孔挤压
1.
Numerical simulation of forging and deep extrusion compound process for axle shaft tube;
半轴套管锻造及深孔挤压复合工艺数值模拟
4) deep extruded area
深挤压
5) extrusion-belt
挤压带
1.
Aimed at Jetta steering knuckle,the technology of two forging steps in one heat was presented,which combined precision pre-forging by extrusion-belt obliterated extrusion with open finish-forging.
以捷达轿车转向节为研究对象,制定了挤压带式可分凹模闭塞挤压精密预制坯和开式终锻成形相结合的“一火两锻”成形工艺。
2.
Aiming at the obliterated extrusion forming with extrusion-belt of pre-forging part,the influences of punch geometry,extrusion-belt length,mould temperature and lubrication to forming technology were discussed by using DEFORM,then the technology parameters used in the forming were acquired.
针对挤压带式闭塞挤压精密预制坯的成形过程,以DEFORM软件为工具,研究了冲头形状、挤压带长度、模具工作温度、润滑等条件对成形工艺的影响,确定了成形过程中需采用的工艺参数。
3.
In this paper, a new precision forming technology is put forward, which combines pre-forging by separable cavity die extrusion-belt type obliterated extrusion with post-forging.
针对轿车转向节这类复杂枝杈类锻件的成形,提出可分凹模挤压带式闭塞挤压预制坯和终锻相结合的精密成形新工艺,介绍了可分凹模闭塞挤压工艺研究的实验结果和数值模拟结果,提出的新工艺具有降低设备公称压力要求和材料利用率高的重要结论。
6) extruded plate
挤压带板
1.
Study on microstructures and mechanical properties of 7055 alloy extruded plate in longitudinal and transverse direction;
7055合金挤压带板纵横向的组织与性能
2.
The effects of single aging,duplex aging and conditions between the first and second step agings on the microstructures and properties of the extruded plate of 7050 aluminium alloy were investigated,by means of TEM,tensile and conductivity tests.
采用力学性能和电导率测试及透射电镜组织观察的方法,研究了7050合金挤压带板的单级时效、双级时效及两级时效之间处理条件对合金组织和性能的影响。
补充资料：冲击挤压(见冷挤压)
冲击挤压(见冷挤压)
impact extrusion
ehongji jiya冲击挤压(impaet extrusion)见冷挤压。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条