1) liquid temperature
液位温度
2) Solution temperature
溶液温度
1.
This article was about the determination of the same sample's absorbent on the condition of different solution temperature, different still time and different water bath temperature,From it we could prove that the result was relative to different experiment conditions.
本文通过对同一样品,在不同的溶液温度、不同的放置时间、不同的水浴加热温度下,测定其吸光度,以证明不同实验条件对测定结果的影响。
3) copper liquid temperature
铜液温度
1.
Soft-sensing model of copper liquid temperature in copper refining process and its application;
铜精炼过程铜液温度软测量模型及应用
2.
Soft-sensing model for copper liquid temperature of heat preservation phase in copper refining rotary anode furnace and its application;
铜精炼炉保温过程铜液温度软测量模型及应用
4) molten steel temperature
钢液温度
1.
By optimizing the technological regulation,importing real-time monitoring,strengthening the management,the molten steel temperature stability can be assured and the breakout rat.
通过优化相关工艺制度,引入实时监控系统,加强管理,可保证连铸钢液温度的稳定性、显著降低漏钢率。
2.
A neural network prediction system of molten steel temperature for VD has been developed.
开发了较完善的 VD炉终点钢液温度在线预报系统 ,应用神经网络方法对 VD炉终点钢液温度进行预报 ,系统在线连续预报了 76炉次 ,预报温度与实际测量温度之差在± 4℃、± 5℃、± 6℃之内的炉次分别占 67。
3.
The prediction model of molten steel temperature for LF VD CC route has been developed by means of meural network method The difference between the predicted and measured temperature was in range of 0 7 ℃ for 85 % heats,and less than 10 ℃ for all heats Because of data replacement function in the model,the prediction precision can be guaranteed regardless of the influence of gradual change factor
利用神经网络方法开发了LF—VD—CC钢液温度预报模型。
5) liquid ammonia temperature
液氨温度
1.
This paper briefly calculates the outlet pressure of high pressure ammonia pump and thecurrent of electromotor under different liquid ammonia temperature,and calculates the saving of pumpsealing and electromotor after increasing the inlet temperature of liquid ammonia.
计算了在不同的液氨温度下高压氨泵的出口压力和电机的电流,并对适当提高入口液氨温度后泵的机封和电机的节约情况进行了估算。
6) Physic liquor temperature
药液温度
补充资料:浓氯化钠注射液 ,高渗氯化钠注射液,高张氯化钠注射液
药物名称:浓氯化钠注射液
英文名:Injection 10% Sodium Chloride
别名:浓氯化钠注射液 ,高渗氯化钠注射液,高张氯化钠注射液
外文名: Injection 10% Sodium Chloride, Hypertonic saline
适应症: 用于脱水症及调节体内水与电解质的平衡。
用量用法: 静脉滴注,临用前稀释,用量与浓度视病情需要而定。
注意事项: 心、肾功能不全者慎用。
规格: 注射剂:1g/10ml,本品为氯化钠的高渗灭菌水溶液。
类别:调节水、电解质及酸碱平衡药
英文名:Injection 10% Sodium Chloride
别名:浓氯化钠注射液 ,高渗氯化钠注射液,高张氯化钠注射液
外文名: Injection 10% Sodium Chloride, Hypertonic saline
适应症: 用于脱水症及调节体内水与电解质的平衡。
用量用法: 静脉滴注,临用前稀释,用量与浓度视病情需要而定。
注意事项: 心、肾功能不全者慎用。
规格: 注射剂:1g/10ml,本品为氯化钠的高渗灭菌水溶液。
类别:调节水、电解质及酸碱平衡药
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条