说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> HeI10830暗点
1)  Hel 10830 dark point
HeI10830暗点
2)  dark spot
暗点
1.
The results indicate the reservoir characteristics and physical property of T1f1-2 is better,its reflection coefficient is bigger than T1f3,and the characteristics of bright spots and dark spots are obvious in Puguang Gasfield.
通过对飞仙关组气藏的岩石学特征、地震反射系数变化特征以及地震响应特征等方面的研究,分析认为飞仙关组一、二段(T1f1-2)储集层物性较好,其地震反射系数比飞三段(T1f3)变化大,"亮点"和"暗点"反射特征表现明显,通过运用地震反射特征进行气田井位部署,应用后取得了较好的效果。
3)  dim spot
暗点
1.
As a result it has the typical seismic reflection characteristics of gas reservoir: 1) dim spot at top interface of gas reservoir, 2) bright spot at bottom interface of gas reservoir, 3) flat spot at gas-water contact, and 4) seismic response shape of gas reservoir.
二连盆地阿尔善背斜下白垩统腾格尔组中部的天然气藏埋深500m,属断背斜层状浅气藏,加之地表条件好,故在地震剖面上出现了典型的气藏地震反射特征,即:①气藏顶界面的暗点;②气藏底界面的亮点;③气水界面的平点;④气藏地震响应的外型。
2.
The seismic and geologic proof is concluded in this article,which can explain the dim spot existed at the deep Kekeya s E 2 k gas reservoir,from studying the acoustic impedance and the surface reflection coefficient of Kekeya gas-bearing carbonate rock.
通过对柯克亚含气碳酸盐岩波阻抗及界面反射系数的研究,取得了柯克亚深部E2k气藏暗点存在的地震地质依据。
3.
We built up a model to identify high efficiency payzones with high permeability by using dim spots of "weak chaotic reflection",and then identified two types of dim spots,i.
以三维三分量地震勘探资料为基础,通过高效储渗区储层测井及波阻抗特征、地震响应特征对比分析、模型正演验证等方法,建立"杂乱弱反射"地震暗点高效储渗区识别模式,划分出PP波/PS波"单弱"及"双弱"2种暗点类型,解剖了其地质及地球物理成因机理,提出"双弱"模式为最优类型。
4)  Scotoma [英][skə'təumə]  [美][skə'tomə]
暗点
1.
Methods Central Scotoma and fixation nature were performed in the patients:20 cases with full-thickness macular hole,10 cases with lamellar macular hole and 10 cases with cystoid macular degeneration.
方法对20例全层黄斑裂孔和10例板层黄斑裂孔及10例囊样黄斑变性患者进行了中心暗点及固视性质检查。
5)  scotoma [英][skə'təumə]  [美][skə'tomə]
暗点,盲点
6)  dark focus
暗焦点
1.
Practical application of laser optometer for dark focus;
暗焦点检查仪的实际应用
补充资料:闭式单点、双点压力机
代码:00413
设备名称:闭式单点、双点压力机
型号规格:公称力≥800kN
计量单位:台
主要参数内容
国际先进国内先进国内一般国内落后评定方法及说明
(一)加工精度
    参照GB10924-89、GB10933-89、JB5200-91
1、滑块下平面对工作台上平面的平行度(mm)
30%精度储备20%精度储备达到规定值大于规定值 
0.02+0.10/100×滑块下平面的被测长度
     
2、滑块行程对工作台上平面的垂直度
30%精度储备20%精度储备达到规定值大于规定值 
0.05+0.02/100×滑块行程长度
     
(二)结构性能
     
1、离合器、制动器接通率,当滑块行程次数≤16次/分时为70%,≤25次/分时为60%,≤45次/分时为50%
大于规定值10%大于规定值达到规定值达不到规定值 
2、液压超负荷保险装置、微调装置、吨位指示器
全部具有全部具有部分具有没有 
(三)噪声dB(A)
     
1、公称力≤400kN
≤85≤87≤88>88 
2、公称力>400kN
≤87≤88≤90>90 
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条