|
|
1) common-offset section
共炮检距剖面
1.
Phase shift method for estimating a common-offset section model;
共炮检距剖面模型的相位移算法
2) zero offset profile
零炮检距剖面
1.
In this paper,the methods of polynomial fitting and wavelet transform to product the zero offset profile and wavelet profile are discussed.
讨论了利用多项式拟合和小波变换制作零炮检距剖面和小波剖面的方法 ,并用VisualC ++语言开发了基于Windows操作平台下的地震资料零炮检距剖面与小波剖面制作系统。
3) offset section
等炮检距剖面
4) common offset
共炮检距
1.
After both first break pickup and trace gathering are fini-shed, the residual time shifts in common-shot,common-receiver and common offsetdomains can be known respectively by taking the top of high velocity layer as thedatum.
本方法以野外获得的表层调查资料和野外静校正量作为初始条件，经初至拾取、道集分选后，以高速层顶板为基准面，在共炮点、共接收点和共炮检距三个域内分别提取剩余时差，进而对大量的数据体进行统计，利用正交迭代求取出全局最优化的剩余静校正量。
2.
After conventional surface consistent deconvolution, data is sorted into common offset gathers and NMO applied, then a second surface consistent deconvolution is run on common offset gathers which el.
该方法在常规地表一致性反褶积之后,对数据进行共炮检距域分选和动校正处理,然后进行主分选为共炮检距域的地表一致性反褶积。
5) zero-offset section
零炮检距地震剖面
6) common offset gather
共炮检距道集
1.
Wave equation pre-stack depth migration for common offset gathers.;
波动方程共炮检距道集叠前深度偏移
补充资料：关于solidworks 中的剖面线中的剖面线
solidworks的剖面线线型定义和autocad相同,它使用了autocad的剖面线定义方法,与autocad通用.因此,可以对剖面线进行定义. 方法:修改\SolidWorks\lang\chinese-simplified\sldwks.prn 用笔记本打开该文件,添加需要的线形.如 ;; Based on AutoCAD Ver.13.0s Hatch Pattern File ;;;; solidworks 区域剖面线定义文件 :: *金属, (Iron BrickStone), ANSI Iron, Brick, Stone masonry 45, 0,0, 0,.125 *塑料, (Lead Zinc Mg), ANSI Lead, Zinc, Magnesium, Sound/Heat/Elec Insulation 45, 0,0, 0,.125 135, 0,0, 0,.125 *玻璃,AR-GLASS@1.0 45,0,0,0,0.5, 0.5,-0.5 45,0,0.1414214, 0,0.5, 0.3,-0.7 45,0.1414214,0, 0,0.5, 0.3,-0.7 *软木, Cork material@1.0 0, 0,0, 0,.125 135, .0625,-.0625, 0,.35355339, .176776696,-.176776696 135, .09375,-.0625, 0,.35355339, .176776696,-.176776696 135, .125,-.0625, 0,.35355339, .176776696,-.176776696 *无, None 删除不需要的定义类型,可以大大提高solidworks 的启动速度
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条
|