1) stress subspace
应力子空间
1.
The characteristics of natural stress modes and stress subspace in finite element were discussed in detail.
详细讨论了有限元本征应力模式和应力子空间的性质,并着重讨论和进一步完善了与杂交应力有限元应力子空间有关的一些定理,为提出新方法提供了理论基础。
2) stress space
应力空间
1.
In 3-D stress space, simplified form of Mohr-Coulomb equivalent area circle yield criterion is derived by adopting analytic geometry method.
在三维应力空间 ,采用解析几何的方法 ,导出了莫尔 -库仑等面积圆屈服准则的简化形式 。
2.
The method of derivation of elasto-plastic constitutive relation is established under general loading law in stress space and strain space.
在此基础上,在应力空间和应变空间中建立了推导一般加载规律的多维增量理论的本构关系的一种途径。
3.
A model for a constitutive relation of rock mass dscribed in stress space is established and its application in engineering is discussed.
在分析岩体细观和宏观损伤特征及其与岩体非弹性变形之间关系的基础上,运用损伤面来定义弹性—损伤准则,建立了在应力空间描述岩体损伤本构关系的一种模型,并对该模型在工程中的应用进行了讨论。
3) Space stress
空间应力
1.
Theoretical analysis and numerical examples show that it is feasible to analyze plane or space stress problems.
基于有限元基本思想,根据微元体与平面桁架单元或空间桁架单元应力、应变等效原则构造出一种更为简单适用的等效铰结桁架单元,理论分析和计算结果表明,用此模型来等效分析计算平面或空间应力问题是可行的,它能达到减少计算工作量,易于分析程序编制,方便数据后处理等目的,并能满足工程精度要求。
2.
Non-liner space stress distribution laws and transfer mechanism of anchorage zone of stayed-cable and steel box girder are mastered and design parameters of anchor structure are optimized.
掌握了斜拉索与钢箱梁锚固区域的非线性空间应力分布规律及传力机理,优化锚固结构的设计参数;同时,提出了减小应力集中的构造措施。
3.
The information asset safety attribute space is established through a space conversion on the information asset attributes, and the dynamic space stress calculation model of the assets of the relationship between attributes is based on space stress function.
通过对信息系统资产的安全属性进行空间转化,构造出信息资产安全属性空间,基于空间应力函数建立了资产属性相互关系动态应力模型。
4) spatial stress
空间应力
1.
On the basis of design of an externally prestressed trial bridge located on certain expressway,the spatial stress simulation model of cable anchorage zone of the bridge is analyzed,the stress distribution and mechanical properties of this key area are studied by bridge analysis software MIDAS/Civil,and the steels distributed for corresponding area are designed using strut-and-tie modle.
结合某高速公路体外预应力试验桥的设计,利用桥梁分析专业软件M IDA S/C iv il对该桥的钢索端部锚固区域进行了空间应力仿真分析,研究了关键区域的应力分布、受力特点。
2.
Based on the structural analysis of the whole model of spatial beam,the spatial stress distribution of back anchorage zone is analyzed by building the geometry model and finite element model of the bridge in ANSYS.
为准确确定大跨度异型斜拉桥的结构受力情况,以采用三角形异型塔、2根水平压杆和1根后斜拉杆交汇于后锚点的、主跨为225m的某大跨度异型斜拉桥为例,在空间杆系模型整体结构分析的基础上,采用ANSYS建立结构的几何模型和有限元模型,分析后锚点的空间应力分布情况。
3.
The bridge spatial stress was finite element analyzed with Midas software,the stress and deformation situation of every component under bridge dead load state were reappeared.
结合一座跨径为116 m的预应力混凝土无背索独塔斜拉桥,对其空间进行静力分析,借用Midas软件对该桥空间应力有限元分析,再现了大桥成桥状态下各构件的应力和变形情况,并初步探讨了无背索斜拉桥的动力特性,以丰富该桥型的研究内容。
5) Hilbert stress subspace
希尔伯特应力子空间
1.
The Hilbert stress subspace of the assumed stress modes is established.
证明了:1)杂交元假设应力模式线性无关是柔度矩阵非奇异的充分必要条件;以及2)等价假设应力模式形成相同的杂交元· 在此基础上建立了假设应力模式的希尔伯特应力子空间,从而可以利用斯密特方法简单地得到等价的正交归一化应力模式,实现了柔度矩阵对角化,使得杂交元形成过程中完全避免了繁杂的矩阵求逆运算,极大地提高了杂交元分析的计算效率,数值算例表明该方法是确实有效的·
6) hybrid finite element stress subspace
杂交元应力子空间
补充资料：轧辊残余应力(见轧辊应力)
轧辊残余应力(见轧辊应力)
residual stresses in roll
zhagun eanyu yingli轧辊残余应力(residual stresses in roll)见礼辐应力。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条