2) end point error
终点误差
1.
The formula can be used to calculate the end point error of both complicated redox reactions and simple ones.
根据氧化还原滴定的特殊规律,运用化学反应的计量关系和能斯特公式,给出了氧化还原滴定终点误差的简单计算公式。
2.
The article discussed the various end point errors of precipitation titrametry,and deduced the computation formula of different titration errors.
讨论了银量法在不同情况下的终点误差,并推导出其各种终点误差的计算通式。
3) endpoint error
终点误差
1.
In order to reduce the endpoint error with indicator in acid-base titration,to improve the accuracy of experimental results,the effects of indicator,and the concentration of the substance which would be determined on endpoint error were studied with theoretical analysis and actual examples.
通过理论分析和实例分析,对酸碱滴定中不同的指示剂、不同浓度的被测物质进行了分析讨论,并根据溶液物料平衡和电荷平衡关系,直接推导得出酸碱滴定终点误差公式。
2.
The problem of the endpoint error in complexometric titradon involves greatly the reliability of determination result or even the method of analysis.
络合滴定的终点误差(TE)问题是关系到测定结果是否准确可靠甚至涉及分析方法本身是否可靠的大问题。
3.
Following the concept of titration errors in oxidation reduction reactions, the establishment and application of the endpoint error in the titration of such reactions in terms of the conditioned potential are discussed emphatically, and a method for increasing the accuracy of titration is described briefly.
从氧化还原滴定误差的概念入手,着重讨论了误差公式的建立及其应用,以条件电位表示的氧化还原终点误差公式以及影响误差的因素。
4) final error
终点误差
1.
The formula of final error in the oxidant reduction titration is deduced according to the principle that the inconsistency of titrating final and chemical calculating point leads to the final error.
根据滴定终点与化学计量点不一致而导致终点误差这一原理,推导出氧化还原滴定的终点误差公式。
2.
This thesis is dealing with sediment titration equilibrium according to Ringbom's additional reaction theory,through which conditional equilibrium constant,sediment curve line equation and final error can be learned.
用林帮的副反应思想处理沉淀滴定平衡、得到条件平衡常数、滴定曲线方程、终点误差 。
5) end error
终点误差
1.
The supplementary study for the end error theory of ringbom
对Ringbom终点误差理论的补充研究
2.
The accurate equation of end error calculation to complexometric titration has been derived.
推导了络合滴定终点误差计算的精确公式,并在特定的条件下还原为林邦误差公式。
6) point error
点位误差
1.
Meanwhile, it also gives the formula of displacement error and point error of any directions in forward intersection, lateral intersection, three point intersection and sides intersectional point.
应用误差椭圆的基本理论 ,由两个任意方向的位差和协方差导出了计算任意方向位差的基本公式 ,并以此为基础 ,非常简洁而新颖地得出了前方交会、侧方交会、后方交会、单三角形和测边交会点在任意方向上的位差和点位误差的公式。
补充资料:闭式单点、双点压力机
| |||||||
主要参数内容 | 国际先进 | 国内先进 | 国内一般 | 国内落后 | 评定方法及说明 | ||
(一)加工精度 | 参照GB10924-89、GB10933-89、JB5200-91 | ||||||
1、滑块下平面对工作台上平面的平行度(mm) | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
0.02+0.10/100×滑块下平面的被测长度 | |||||||
2、滑块行程对工作台上平面的垂直度 | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
0.05+0.02/100×滑块行程长度 | |||||||
(二)结构性能 | |||||||
1、离合器、制动器接通率,当滑块行程次数≤16次/分时为70%,≤25次/分时为60%,≤45次/分时为50% | 大于规定值10% | 大于规定值 | 达到规定值 | 达不到规定值 | |||
2、液压超负荷保险装置、微调装置、吨位指示器 | 全部具有 | 全部具有 | 部分具有 | 没有 | |||
(三)噪声dB(A) | |||||||
1、公称力≤400kN | ≤85 | ≤87 | ≤88 | >88 | |||
2、公称力>400kN | ≤87 | ≤88 | ≤90 | >90 |
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条