1) squeezing degree
压缩度
1.
Our results show that the squeezing degree and squeezing direction of the output optical image can be controlled by the parametric image amplifier,namely,the increase or decrease of the squeezing degree and the change of the squeezing direction are dependent on the parameter selection of the parametric image amplifier.
结果表明:参量图像放大系统能够控制输出光学像的压缩度和压缩方向,即压缩度的增加与减小和压缩方向的改变决定于参量图像放大系统的参数选择。
2) degree of squeezing
压缩度
3) compression strength
压缩强度
1.
Preparation of high compression strength polyacrylate/polysiloxane interpenetrating network hydrogel;
高压缩强度聚丙烯酸盐/聚硅氧烷互穿网络水凝胶的制备
2.
The compression strength of pitch derived car.
将高温煤沥青和浸渍剂沥青在不同压力下炭化,在2500℃下对所得沥青炭进行石墨化处理;测试了所得沥青炭的体积密度、开孔率;利用扫描电子显微镜(SEM)观察了所得沥青炭的显微结构;利用XRD检测了所得沥青炭石墨化处理后的石墨化度;测试了所得沥青炭的压缩强度。
3.
The structure,thermal stability,especially the effects of isothermal annealing on the microhardness and compression strength of this bulk metallic glass were investigated by X-ray diffraction,differential scanning calorimetry,microhardness and compression tests.
采用X射线衍射(XRD)、示差扫描量热(DSC)、显微硬度及压缩试验等方法研究了非晶合金的结构、热稳定性,特别是等温热处理对其显微硬度与压缩强度的影响。
4) compressive strength
压缩强度
1.
3D fiber waviness model and prediction of compressive strength of stitched laminates;
缝合复合材料层板三维纤维弯曲模型及压缩强度预报
2.
Computational modified model and experimental verification of compressive strength of the X-cor sandwich
X-cor夹层结构压缩强度模型改进与实验验证
3.
Experimental study on uniaxial compressive strengths of artificial freshwater ice
人工淡水冰单轴压缩强度试验研究
5) compressive stiffness
压缩刚度
1.
In order to study the mechanical property of explosive crystals with different qualities,two recrystallized and a commercial grade RDX and HMX particles were selected and tested by compressive stiffness method.
分别选取三种不同品质的RDX和HMX颗粒集合体进行压缩刚度实验,并采用Kawakita压制模型对压制曲线进行拟合分析,得到评价晶体颗粒力学性能的具有模量量纲的常数。
6) Deformation rate
压缩程度
1.
We made TPA test on apple slices to investigate the influence of deformation rate and degree of compression on TPA test results.
本文简要介绍了TPA质构分析方法,具体阐述了TPA质构参数的含义,并对苹果片进行TPA测试,研究压缩速率和压缩程度对测试结果的影响。
补充资料：压缩式塑度计
分子式：
CAS号：
性质：测定与塑性流动有关的屈服值或塑性黏度的仪器。
CAS号：
性质：测定与塑性流动有关的屈服值或塑性黏度的仪器。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条