1) configuration
[英][kən,fɪɡə'reɪʃn] [美][kən'fɪgjə'reʃən]
构态
1.
Analysis on configuration and kinematics of typical metamorphic mechanism;
一个典型变胞机构的构态与运动学分析
2.
On Classification and Configuration Analysis for Metamorphic Mechanisms;
变胞机构的分类及其构态分析
3.
The configuration transformation was analyzed,and the adjacency matrixes under various metamorphic mechanisms were put forward.
提出了一种具有特殊结构的六杆球面变胞机构,并对该机构进行了构态变化分析,给出了在不同构态时机构的邻接矩阵。
2) morphology and structure
形态结构
1.
The measurement of DMTA and SEM was used to study the morphology and structure of the cured epoxy, identifying the degree of phase segregation and the effect of toughening in the cured epoxy.
以液体聚硫聚脲齐聚物来增韧环氧-聚酰胺体系,用DMTA和SEM研究了固化后环氧树脂的形态结构、相分离程度和增韧效果。
2.
Its morphology and structure are analyzed by transmission electron microscope and infrared spectrometer.
本文考察了硼的引入对聚硅酸稳定性的影响 ,利用透射电镜及红外光谱观测了其形态结构。
3.
Histo morphology and structure of female reproductive ducts in Bactrian camel were investigated by histological methods.
应用组织学方法观察了雌性空怀双峰驼生殖道的形态结构。
3) morphological structure
相态结构
1.
Effects of coupling agents on curing characteristics and physical-mechanical properties of the two kinds of composites were investigated,and the morphological structure of the composites were observed by scanning(electron) microscope.
采用乳液共混法制备了淀粉/丁苯橡胶(SBR)以及间苯二酚甲醛树脂(RF)改性淀粉/SBR复合材料,考察了偶联剂对2种复合材料硫化特性、力学性能的影响,并用扫描电镜观察了其相态结构。
2.
The morphological structure of dynamically vulcanized thermoplastic(elastomer)(TPV) ethylene propylene diene monomer(EPDM)/polypropylene(PP) was investigated with scanning electron microscope.
用扫描电镜研究了三元乙丙橡胶(EPDM)聚/丙烯(PP)动态硫化热塑性弹性体(TPV)相态结构的形成过程,探讨了交联密度、制备工艺、螺杆转速对EPDM/PP TPV相态结构的影响。
3.
The morphological structures of NBR/PP TPV were analyzed.
苄酯4种增塑剂对丁腈橡胶(NBR)聚/丙烯(PP)热塑性硫化胶(TPV)邵尔A硬度、耐油性能和流变性能的影响,并用透射电镜分析了4种增塑剂对NBR/PP TPV相态结构的影响。
4) liquid structure
液态结构
1.
Research on the Liquid Structure of Lead-free Solders and the Interfacial Reaction during Soldering and Their Correlation;
无铅钎料的液态结构与钎焊界面反应及其相关性研究
2.
The liquid structures of two molten lead-free solders,Sn-0.
7Cu和Sn-2Cu(质量分数,%)钎料在260,330和400℃的液态结构。
3.
The liquid structure and melt treatment of M963 Ni base superalloy have been studied by using high temperature X-ray diffraction.
通过液态X射线衍射研究了铸态镍基高温合金M963的液态结构和熔体处理。
5) Morphological Structure
形态结构
1.
Characterization of down morphological structure;
羽绒纤维的形态结构表征
2.
Effect of alkali treatment on morphological structure and mechanical properties of PTT fiber;
碱处理对PTT纤维形态结构和力学性能的影响
3.
Study on the crystallization properties and morphological structure of cationic dyeable polypropylene fibers;
阳离子染料可染丙纶的结晶特性和形态结构研究
6) Morphology
[英][mɔ:'fɔlədʒi] [美][mɔr'fɑlədʒɪ]
形态结构
1.
Study on the morphology of electrospinning silk fibroin nanofibers nonwoven membrane;
静电纺丝素纳米纤维非织造膜形态结构研究
2.
Effect of coagulation conditions on morphology of as-spun PAN fiber during wet spinning;
湿纺凝固条件对PAN初生纤维形态结构的影响
3.
Electrospinning process and the morphology of electrospun;
电子纺丝成形及纤维形态结构研究
补充资料：构构
1.关系恶化貌。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条