1) inertia moments
地球转动惯量
1.
The inertia moments of the equivalent inner core ellipsoid are calculated, and then the largest contribution of the inner core to the difference between the Earth’s principal inertia moments A and B,is given.
基于内核的基本特征,引入等效内核椭球概念,计算了等效内核椭球的转动惯量,进而给出了内核对地球转动惯量A和B的差异的最大贡献,其量级大约是目前较公认数值(B-A)/C=2×10-5的四分之一。
2) moment of inertia-variable ball rotor
变转动惯量球转子
1.
In this paper,the theory of moment of inertia-variable ball rotor which is applied to small caliber fuse is put forward.
文中提出了应用于小口径引信延期解除保险机构的变转动惯量球转子原理,对变转动惯量球转子进行了结构优化设计和测试。
2.
In this paper,the theory of moment of inertia-variable ball rotor which is applied to small caliber fuse is put forward,the structural project of the moment of inertia-variable ball rotor and the measuring project using centrifugal machine to testify the correctness of the principle and measure the delay safety time.
介绍了变转动惯量球转子延期解除保险机构的原理,为了证明此原理的正确性和测量其延期解除保险的时间,设计了一套变转动惯量球转子结构方案以及在离心机上做实验的测试方案。
3) Moment of inertia
转动惯量
1.
The application of moment of inertia real time compensation in the rewinder web tension control;
转动惯量实时补偿在复卷机纸幅张力控制中的应用
2.
Measuring method and error analysis on moment of inertia of complex shaped components;
复杂形状构件转动惯量的测量方法及误差分析
4) rotary inertia
转动惯量
1.
Eigenfrequencies of beams considering the effects of shear distortion and rotary inertia;
考虑剪切变形和转动惯量影响的梁的固有频率计算
2.
The effect of shear deformation and rotary inertia are considered in the paper.
文中考虑了剪切变形和转动惯量的影响。
3.
Based on the principle of compound pendulum,the measurement method and corresponding equipment for the centroidal deviation and the rotary inertia of rocket projectile were described.
基于复摆原理,阐述了箭弹的质偏和转动惯量的测量方法及装置,推导出了质偏和转动惯量的计算公式。
5) rotational inertia
转动惯量
1.
Study of calculation method for rotational inertia of a uniform rod to random rotation shaft;
均匀细杆对任意轴转动惯量的计算方法
2.
Study on the error and approximate expressions of the rotational inertia based the theory of momentum;
基于动量矩原理的转动惯量近似表达及分析
3.
A new measuring method of rigid - body rotational inertia——compound pendulum method;
刚体转动惯量的一种新型测量法——复摆法
6) rotating inertia
转动惯量
1.
The error analysis through the experiment of rotating inertia with a tri-linear pendulum;
由三线摆测转动惯量谈误差分析
2.
Research on relation between friction torque and mass m_0 for rotating inertia apparatus;
转动惯量仪摩擦力矩与质量m_0关系研究
3.
A method for calculating the rotating inertia of vibration structure was recommendation.
本文介绍了一种自动计算振动结构的转动惯量的方法。
补充资料：水轮发电机转动惯量
水轮发电机转动惯量
rotational inertia of hydrogenerator
shullun fodlonl一zhuondong guonl旧ng水轮发电机转动惯.(rotational inertia ofhydrogenerator)水枪发电机转动惯盆是发电机转动部分的重tG与其惯性直径D平方的乘积，用GDZ表示，也称为转动部分的飞轮力矩。 转动惯量表明电力系统出现大干扰时，水轮发电机组转动部分保持原来运动状态的能力，所以对电力系统的暂态过程和动稳定有很大影响。转动惯t对水轮机调节保证计算也有很大影响，转动惯t大，机组甩负荷后的转速上升率如保持一定值，则可允许较大的压力上升率，从而可以减小引水钢管直径或允许增加钢管长度，甚至不设调压井.但增大转动惯t将增加发电机重量和造价，也延长了机组的起动时间。 当水轮发电机基本尺寸确定后，转动惯量GDZ值可按下列经验公式计算 GDZ=kD户·”1.式中D为定子铁芯内径，m‘l:为定子铁芯长度，m;h为经验系数，一般可按表选取。 经脸系傲裹┌────────┬────┬────┬────┐│机纽转迫(r/成.) │<100 │100~375 │>375 │├────────┼────┼────┼────┤│经玻系狱《k) │5 .2~5.5│5.1~5。3│4.5~5.0 │└────────┴────┴────┴────┘ 大容量低转速水轮发电机组的转动惯t最大已达450000 tf·mZ(4410 kN·mZ)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条