1) predigestion method
简化画法
1.
One current predigestion method on circular isometric project paralleled coordinate plane;
一种通用的平行于坐标面圆轴测投影的简化画法
2) Brief drawing method
简捷画法
3) simple painting
简便画法
1.
Based on this,we consider a map of the internal forces simple painting and avoid complex calculations,through direct observation of paint.
基于此,采用一种内力图的简便画法,避免复杂的计算,通过观察直接画出。
4) simplified method
简化法
1.
Because it was fussy to calculate average hydraulic grade and workload is great,a simplified method was adopted in this article.
本文采用一种简化法计算明渠水面曲线 ,不必计算平均水力坡度 ,可使计算工作量大为减少 。
5) simplified method
简化方法
1.
A planar simplified method for three-dimension cement-soil mixing piles composite foundation with FEM numerical analysis;
搅拌桩复合地基平面模拟的简化方法探讨
2.
A simplified method for tooth surface equation of an equal-height spiral bevel gear;
一种等高齿螺旋锥齿轮齿面方程的简化方法
3.
Based on the differences of structural response between multi-dimensional excitation and simple-dimensional excitation,a simplified method to calculate member forces under multi-dimensional and multi-support excitation is presented in this paper.
在对多维输入和一维输入进行比较分析的基础上,建立了多维多点输入下计算杆件内力的简化公式,通过计算多维一致输入、一维一致输入和一维多点输入下的杆件内力,可由简化方法得到多维多点输入下的杆件内力,将模拟地震波的时间缩短了一半。
6) simplified algorithm
简化算法
1.
This paper presents a simplified algorithm based on an optimization objective function.
基于PLS算法的优化函数形式,该文提出一种新的PLS优化目标函数及相应简化算法。
2.
To greatly reduce the computational complexity of FFOC and improve the practicability in the engineering, the relation between FFOC recursive estimate and its computational complexity is studied, and simplified algorithm for calculating .
为了解决这一问题,研究了非平稳随机过程五阶累积量递推计算与计算量的关系,提出了五阶累积量计算的简化算法。
补充资料：齿轮画法
在机械制图中，齿轮的轮齿部分作图繁琐。为提高制图效率，许多国家都制订了齿轮画法标准，国际上也制订有ISO标准。中国机械制图国家标准规定:①齿顶圆和齿顶线用粗实线绘制。②分度圆和分度线用点划线绘制。③齿根圆和齿根线用细实线绘制，或省略不画。在剖视图中,齿根线用粗实线绘制(图1)。标准还规定了两齿轮啮合时啮合区的画法，如圆柱齿轮在垂直于齿轮轴线的投影面的视图中，啮合区内齿顶圆均用粗实线绘制，或省略不画。在平行于齿轮轴线的投影面的视图中，啮合区的齿顶线不须画出，节线用粗实线绘制。在剖视图中，啮合区内一个齿轮的齿顶线用粗实线绘制,另一个齿轮被遮挡的齿顶线用虚线绘制（图2）。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条