说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> G-morphic模
1)  G-morphic module
G-morphic模
1.
So we can find some links between G-morphic modules and G-morphic ring from the results of this paper.
利用模的自投射及生成核的性质给出了左R模为G-morphic模等价于其自同态环为左G-morphic环的条件,并利用此结论证明了G-morphic模有类似于G-morphic环的性质:在一定条件下G-morphic模的直积因子也为G-morphic模,从而在一定程度上反映了G-morphic模与G-morphic环的联系。
2)  G-morphic ring
G-morphic环
1.
The following results have been given: let R be a ring and G be a locally finite group,if the group ring RG is a left G-morphic ring,then R is a left G-morphic ring;if the group ring RH is a left G-morphic ring for every finite subgroup H of G,then the group ring RG is a left G-morphic ring.
本文讨论了左G-morphic群环RG的性质,主要证明了以下结果:设R是一个环,G是一个局部有限群,如果群环RG是左G-morphic环,那么R是左G-morphic环;如果对G的每个有限子群H,群环RH是左G-morphic环,那么群环RG是左G-morphic环。
2.
We show some relations of morphic ring,G-morphic ring,PP-ring,GPP-ring,Bear ring and regular ring.
讨论了morphic环,G-morphic环,PP环,GPP环,Bear环与正则环之间的关系。
3)  left G-morphic
左G-morphic
1.
In this paper we give the condition under which a left R module is G-morphic if and only if its endomorphism ring is left G-morphic by discussing the properties of self-projective and generating kernels in left R modules.
利用模的自投射及生成核的性质给出了左R模为G-morphic模等价于其自同态环为左G-morphic环的条件,并利用此结论证明了G-morphic模有类似于G-morphic环的性质:在一定条件下G-morphic模的直积因子也为G-morphic模,从而在一定程度上反映了G-morphic模与G-morphic环的联系。
4)  left G-morphic ring
左G-morphic环
1.
Moreover,we show that: If R is a left G-morphic ring,the same is true of eRe for every idempotent e∈R;Every unit π-regular ring is a left(right) G-morphic ring;Every left G-morphic ring is a right GP-injective ring.
我们给出了G-morphic环的定义,证明了如下主要结果:对R中的任意幂等元e,如果R是左G-morphic环,则eRe也是左G-morphic环;每一个幺π-正则环是左(右)G-morphic环;每一个左G-morphic环是右GP-内射环。
5)  morphic module
morphic模
6)  left(right) G-morphic ring
左(右)G-morphic环
补充资料:凹模、凸凹模工作型面加工工艺过程
1)备料。 n
    2)锻造。锻成长方形的坯料(每件留长工艺夹头)。 n
    3)热处理。退火。   n
    4)铣(刨)削。铣(刨)削六面成长方形模块。 n
    5)磨削。磨削上、下两端面及相邻两侧面,用90。角尺测量相邻两面的垂直度。 n
    6)钳工加工。用平板和划线盘按图划线,并打样冲眼;用钻头钻螺纹底孔;用圆柱销孔的预孔;用钻头钻挡料销让位孔;用钻头在中心处钻穿丝孔等;正、反面孔口倒角;凸凹模用钻头孔扩,保证刃口高度;攻螺纹;铰孔。n
  7)铣削。平口钳装夹工件;用的立铣刀铣削型孔至尺寸,保证深度。 n
   8)热处理。凹模工件淬硬至HRC60~64,凸凹模工件淬硬至HRC58~62。 n
   9)平磨。磨上、下两端面及相邻两侧面,用90。角尺测量相邻两面的垂直度至图要求;退磁。 n
   10)线切割。按图编制线切割程序,切割模型孔成形,留单面研磨余量0.005 mm。 n
   11)钳工加工。研光线切割面: n
   12)检验。 n复合冲裁模的装配应选择凸凹模作为装配基准件,先装下模部分,后装上模部分
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条