1) compusite beams/maximum steel ratio
叠合梁/最大配筋率
2) the maximum reinforcement ratio
最大配筋率
3) maximum and minimum reinforcement ratio
最大和最小配筋率
4) minimum reinforcement ratio
最小配筋率
1.
Simplied calculation to the minimum reinforcement ratio of flexural members to be content crack;
满足裂缝要求的受弯构件最小配筋率的简化计算
2.
Based the definition of the minimum reinforcement ratio of the reinforced concrete column,the minimum reinforcement ratio of the compressive and flexural concrete members reinforced with FRP tendons was introduced.
分析了FRP筋混凝土压弯构件发生受拉破坏时混凝土的等效应力图,依据钢筋混凝土结构最小配筋率的定义,给出了FRP筋混凝土压弯构件的最小配筋率。
5) optimal reinforcement ratio
最佳配筋率
1.
The optimal reinforcement ratio for a slab corresponds to its maximum energy absorption capacity.
采用TM-5和ASCE推荐的单自由度体系简化RC简支单向板,选用双折线模型计算RC板的R-y曲线,分析不同配筋率的R-y曲线下方面积,面积最大时的配筋率即为该设计的最佳配筋率,改变板的几何尺寸,按上述方法分别得出不同设计方案的最佳配筋率。
2.
After comparing the areas under the R-y curves of RC slabs with different reinforcement ratios,the reinforcement ratio responding to the biggest area can be defined as the optimal reinforcement ratio.
对爆炸载荷作用下RC板的R-y曲线采用双折线模型,计算不同配筋率的R-y曲线下方面积,面积最大时的配筋率即可定义为相应设计的最佳配筋率。
3.
Comparing the areas under the resistance-deflection curves of RC slabs with various reinforcement ratios,the reinforcement ratio corresponding to the biggest area can be defined as an optimal reinforcement ratio.
分析不同配筋率的R-y曲线下方面积,面积最大时的配筋率即可定义为相应设计的最佳配筋率。
6) minimum ratio of reinforcement
最小配筋率
1.
In accordance with The Code for Designing Concrete Structures and based on the formula for calculating maximum crack width, some formulas for computing minimum ratio of reinforcement to effective tensile region which satisfy the requirement of crack width are derived.
依据现行《混凝土结构设计规范》最大裂缝计算公式及其验算条件,推导出相关公式,编程计算出满足裂缝宽度要求的有效受拉区最小配筋率,并汇编成表格供直接计算满足裂缝宽度要求的配筋时查用。
补充资料：叠梁闸门
叠梁闸门
stop log gate
根插入门槽以封闭水道孔口的闸门，也称插板(见图)。制造叠梁闸门的材料有木材、钢材和钢筋混凝土等，目前多半用在中小型水工建筑物上作为检修闸门。叠梁闸门构造简单，制作方便，但接缝较多，漏水量较大，操作也较麻烦。20世纪70年代发展了一种浮式叠梁闸门，是四周密封的箱形梁，可利用浮力减少门重，在水面上利用挂钩梁操作，较为方便。(夏念凌)叠梁闸门d ieliang zhamen叠梁闸门(stop109 gate)由若干根独立的横梁逐
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条