1) stiffness jump
胶接应力
1.
According to a proposed method to calculate adhesive stresses by using node forces,the adhesive stresses between stiffeners and skin were computed in two typical cases: stiffener stiffness jump and postbuckling progressive failure.
用拟协调板元和梁元离散飞机尾翼翼面典型复合材料加筋壁板,对长桁截面刚度突变和面板后屈曲剧烈变形两种导致脱胶情况分别进行了线性前屈曲和非线性后屈曲逐渐破坏有限元分析,利用文中提出的节点力法,计算长桁与面板间的胶接应力。
2) cementation effect
胶接效应
3) contact stress
接触应力
1.
Calculation of Interface Width and Contact Stress of Spinning Top Roller and Roller;
细纱胶辊与罗拉接触面宽度和接触应力的计算
2.
The calculation of contact stress of rock bit floating ring journal bearing under disalignment;
不对正情况下牙轮钻头浮动套轴承接触应力计算
3.
Numerical simulated analysis of the contact stress on the sealing rubber of the packer;
封隔器胶筒接触应力的数值模拟分析
4) welding stress
焊接应力
1.
3D-FEM numerical simulation of welding stress in thin aluminum alloy plate;
铝合金薄板焊接应力三维有限元模拟
2.
On the control of welding stress and deformation;
浅谈焊接应力与变形的控制
3.
Measures to control welding stress and deformations;
如何控制焊接应力和变形
5) contacting stress
接触应力
1.
This paper focuses on the contacting stress between the plunger and the seal ring,and analyzes the effect of the seal ring structure parameters on the contacting stress.
文章从柱塞与密封圈接触应力构成的角度出发,分析研究压裂泵V形往复密封圈结构参数对接触应力的影响,对密封结构参数进行了优化,为密封圈的结构设计提供理论依据。
2.
On the basis of theoretical study on the high speed cylindrical roller bearing a finite element analysis was carried out on the common steel bearings and the ceramics bearings, and the influence of rotary speed on the contacting stress and the equivalent stress.
在高速圆柱滚子轴承理论研究的基础上,对普通钢制轴承和陶瓷轴承进行有限元分析,研究了转速对接触应力和等效应力的影响。
3.
According to the calculation on the contacting stress and the linear speed of the gear in the hoist of the 16t-30m portal crane,the N460 heavy duty industrial gear oil was selected instead of the recommended lube oil in instruction book.
通过对16T-30M门机卷扬减速器齿面接触应力与齿轮线速度的计算,对使用说明书推荐的润滑油品进行了重新修订,选择了N460号重负荷工业齿轮油。
6) contact pressure
接触应力
1.
Based on large quantity of observed results,the contact pressure on soil between piles and the contact pressure on piles are assumed to distribute in a parabolic form.
在大量实测研究结果的基础上 ,假定复合地基桩间土和桩的接触应力按抛物线模式分布 ,通过地基与结构共同作用条件的满足来确定复合地基的接触应力的具体分布 ,使考虑共同作用的沉降计算成为可能 ,并对最大沉降和差异沉降受结构对地基的相对刚度的影响规律进行分析 ,得出若干有益的结论。
2.
Having studied present analysis method on the contact pressure of flexible bearings.
提出了一种分析计算柔性轴承载荷分布和接触应力的方法、对于按照动负荷能力来计算柔性轴承的许用载荷具有一定意义。
补充资料:接应
①配合自己一方的人行动:你们先冲上去,二排随后~。②接济;供应:粮草~不上。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条