1) connective element
![点击朗读](/dictall/images/read.gif)
联结单元
1.
parameters element,elasto-plastic steel bar element, both direction connective element and function of examining material failure and distributing anew of disequilibrium force are introduced.
提出了反复荷载作用下钢筋混凝土结构的非线性分析方法,程序中引入了混凝土平面等参单元、弹塑性钢筋单元和双向联结单元,还引入了检验材料破坏及其破坏时的不平衡力重分布等功能,采用了片状裂缝模型,以混合型的初始刚度法与切线刚度法进行非线性选代计算。
2) single-spring joint element
![点击朗读](/dictall/images/read.gif)
单弹簧联结单元
1.
Based on the traditional double-spring joint element method,a new method—single-spring joint element method based on the mixed coordinate system, was proposed for bond-slip problems of steel bars and concrete.
在传统双弹簧联结单元法的基础上,提出了一种求解钢筋与混凝土黏结滑移问题的新方法——基于混合坐标系的单弹簧联结单元法。
4) cells cascaded
![点击朗读](/dictall/images/read.gif)
单元串联
1.
Various modulation strategies of cells cascaded multilevel inverter are analyzed and researched.
对多电平变频器不同的拓扑结构进行比较,研究分析单元串联多电平变频器的几种不同的调制策略。
2.
A kind of cells cascaded multilevel high voltage inverter that has been developed recently is introduced.
介绍了一种新型单元串联多电平高压变频器 ,详细阐述了单元串联多电平高压变频器的工作原理、系统结构以及脉冲控制的策略 ,并通过系统仿真研究 ,分析了高压变频调速装置的技术
5) cell combination
![点击朗读](/dictall/images/read.gif)
单元和联
1.
According as the mission of the magazine s detecting system,the present article analyzed the relation between all the smart sensor and the macrocosmic effect of the smart sensor s network,found and calculated the cell combination connection model of mission reliability,expounded the rationality of the cell combination connection model applied to the smart sensor s network.
针对弹库探测系统的智能传感器网络,结合其具体功能,分析了网络中各个传感器之间的相互关系和网络的整体效果,构建了单元和联任务可靠性模型并进行分析计算,阐述了其应用于智能传感器网络的合理性。
6) series units
![点击朗读](/dictall/images/read.gif)
单元串联
1.
To solve the problem that high voltage frequency inverter has pollution to electric network and electric equipments, a method of series units was adopted to design a frequency inverter having a new topological structure.
针对高压变频器对电网和用电设备产生电磁污染的问题,采用单元串联的方法,设计了一种新型拓扑结构的高压变频器。
补充资料:变压器联结组别
变压器联结组别
connection of transformer windings
黔备番 皿B.述丛从 D,一\!·厂瓤]y,d“尹第砂‘于一士于“Y,z \.肚上」谓贵念 B BB碘遂远用联结组标号表示的三相变压器的绕组联结标志示例(二) 注:有“,”者为常用的联结方式。压(如果有)及低压绕组的联结方式,且表示中压、低压绕组对高压绕组相位移关系的通用标号,也称联结组标号。三相变压器的三个相绕组或组成三相绕组的三台单相变压器相同电压的绕组可连接成星形、三角形或曲折形等,其高压绕组相应用大写字母Y、D或z表示:中压和低压绕组相应用同一字母的小写形式y、d或:表示。对有中性点引出的星形或曲折形连接的绕组,其高压绕组侧分别以YN或ZN表示,中压和低压绕组侧分别以yn或:n表示。对自藕变压器,额定电压低的绕组(公共部分)用字母aut。或a表示,如连接为YNaut。或YNa,则表示为中性点引出的星形连接的自藕变压器。 当有稳定绕组(不与外部负载相连的三角形连接绕组)时,应在负载绕组字母后用“十d”表示。其稳定绕组没有相位移标志。 绕组连接可变时(如:申一并联或Y一D),两种连接连同相应的额定电压均应给予标志。例:220(110)/10.skV YN(YN)dll。 不同电压绕组的相位移是指某两个不同电压的绕组中,各相应端子与中性点间电压相量之间的角度差.用钟时数表示的相位移,是将其高压绕组的一个端子相t(分针)定在假定时钟的12点上,此时有一定相位移的低压绕组相应端子相量(时针)所指的时数即代表联结组别,如YNdll。从理论上讲,可以有多种不同的联结组别,但实际常用的并不多。如图所示为用联结组标号表示的三相变压器的绕组联结方式标志示例。口旧「lyU目万“LJ曰】.。‘口训。变压铃联结组别(connection of transformer用一组字母和时钟序数指示高压、中豁蹂易黔黔黔黔﹁"IJ S︸﹃.﹄︸、、口﹄﹄ng丁工-..丁土一尸炸咕手t一,d尸‘‘义舀t亡七﹄一.亡‘工去更公舍1n。尸.1﹄!沐伙.LW文。飞戎.二‘文。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条