|
|
1) frequency division section
分频剖面
2) single frequency section
单频剖面
3) time-frequency profile plot
时频剖面图
1.
The analysis is expressed in terms of harmonic wavelet time-frequency map,time-frequency contour map and time-frequency profile plot.
介绍了谐波小波分析的基本原理及其快速算法,利用谐波小波时频图、时频等高线图以及时频剖面图挖掘管道泄漏敏感特征,准确提取负压波拐点,实现了对长输管线小泄漏的故障诊断。
4) distribution in profile
剖面分布
5) profile distribution
剖面分布
1.
The profile distribution of FDA hydrolsis in paddy soils in Taihu region;
太湖地区典型水稻土FDA水解酶活性的剖面分布特征
2.
Seven profiles(6 paddy soils plus 1 reference dry cropland soil) from southern Jiangsu were chosen to study the profile distribution of total contents of Cu,Pb,Hg and As under different environmental impacts.
重金属剖面分布特征可以在一定程度上反映水稻土的重金属污染积累程度。
3.
A comparative study was made on the profile distribution of exchangeable Ca and Mg and Ca/Mg ratio at the depth of 0-150 cm in an aquic brown soil under four land use patterns,i.
在水稻田、玉米地、撂荒地和人工林地4种土地利用方式下,对潮棕壤0~150 cm土层中土壤交换性钙(Ca)和交换性镁(Mg)的剖面分布及Ca/Mg的变化进行了比较研究。
6) face partition
面剖分
1.
Based on duality principle, the enumerating equation of undetachable-edge rooted planar map with face partition is extended, obtaining an enumerating equatim whose explicit equation, with number of edges being parameter, is derived by means of quadric form and lagrange inversion theorem.
根据对偶关系 ,即其对偶图的边不可分离有根平面地图的依面剖分计数方程 ,对其进行了推广 ,得到了无环有根平面地图依根节点度数、边数和节点个数为参数的计数方程 。
2.
In this paper the author got the enumeration equation of edge-non-separable with face partition, and also abtained its enumeration equation and expression with rooted face degree, edges and faces.
得到了边不可分离有根平面地图依面剖分的计数方程 ,并得到其依根面度数、边数和面数三参数的计数方程及有关计数显
补充资料：关于solidworks 中的剖面线中的剖面线
solidworks的剖面线线型定义和autocad相同,它使用了autocad的剖面线定义方法,与autocad通用.因此,可以对剖面线进行定义. 方法:修改\SolidWorks\lang\chinese-simplified\sldwks.prn 用笔记本打开该文件,添加需要的线形.如 ;; Based on AutoCAD Ver.13.0s Hatch Pattern File ;;;; solidworks 区域剖面线定义文件 :: *金属, (Iron BrickStone), ANSI Iron, Brick, Stone masonry 45, 0,0, 0,.125 *塑料, (Lead Zinc Mg), ANSI Lead, Zinc, Magnesium, Sound/Heat/Elec Insulation 45, 0,0, 0,.125 135, 0,0, 0,.125 *玻璃,AR-GLASS@1.0 45,0,0,0,0.5, 0.5,-0.5 45,0,0.1414214, 0,0.5, 0.3,-0.7 45,0.1414214,0, 0,0.5, 0.3,-0.7 *软木, Cork material@1.0 0, 0,0, 0,.125 135, .0625,-.0625, 0,.35355339, .176776696,-.176776696 135, .09375,-.0625, 0,.35355339, .176776696,-.176776696 135, .125,-.0625, 0,.35355339, .176776696,-.176776696 *无, None 删除不需要的定义类型,可以大大提高solidworks 的启动速度
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条
|