2) induced velocity
![点击朗读](/dictall/images/read.gif)
诱导速度
1.
A method of spatial distribution of helicopter rotor induced velocity;
![点击朗读](/dictall/images/read.gif)
旋翼诱导速度空间分布的一种计算方法
2.
The radial distribution of vertical induced velocity of coaxial-rotor flow fields is mainly investigated.
采用PIV(粒子图像测速)技术,对共轴式双旋翼在悬停和以不同速度前飞时的流场进行水洞试验,测量得到旋翼流场的速度和涡量分布,主要研究了共轴式双旋翼流场的垂向诱导速度沿径向的分布规律。
3.
While it is applied to the formulas found in the page, the induced velocity of cont.
![点击朗读](/dictall/images/read.gif)
为了在固定尾迹分析中更好地描述桨叶附着涡环量分布,结合叶素理论,采用一个三角级数表达附着涡环量的连续分布,并应用于悬停状态下单旋翼和共轴双旋翼的气动特性分析,通过小量计算即获得连续光滑的附着涡环量分布,将其应用到推导的公式中计算出连续分布的诱导速度,进而分析了共轴双旋翼上下旋翼气动干扰及扭矩平衡条件。
3) induced velocities
![点击朗读](/dictall/images/read.gif)
诱导速度
1.
The rotor wake induced velocities at the position of 0.
![点击朗读](/dictall/images/read.gif)
建立了旋翼自由尾迹模型 ,求解了悬停状态下桨盘下方 0 1R处的旋翼诱导速度分布 ,计算结果与实验数据吻合较好 ,并对计算结果进行了简要的分
2.
A method is given for calculating induced velocities by a wake vortex line which results in a rapid convergence.
建立了旋翼升力线模型和广义尾迹模型,在计算角迹涡线诱导速度时,采用了快速收效方法。
5) induced velocity field
![点击朗读](/dictall/images/read.gif)
诱导速度场
1.
With the help of Apollonius conformal transformation and Fourier series method obtained is an induced velocity field of steam bubble growth process in a stationary flow field.
通过使用Apolonius保角变换和Fourier级数方法,获得了静止流场中汽泡生长过程中的诱导速度场。
6) induced potential
![点击朗读](/dictall/images/read.gif)
诱导速度势
1.
The algorithms for calculating induced potentials and velocities due to some axisymmentric singularity elements in common use are presented in this paper.
本文给出轴对称问题线元上高次分布源和偶极在无界域中的诱导速度势和诱导速度的计算公式,可供用分布奇点法求解轴对称势流问题时参考。
2.
The algorithms for calculating induced potentials and velocities dee to distributed singularity on an axisymmetric element are presented.
本文给出分布在轴对称面元上的奇点在无界域中的诱导速度势和诱导速度计算公式,奇点分布强度在轴向和径向采用高斯分点离散,周向采用富氏级数离散。
补充资料:DWP喷射气流干燥机
![](/picture/bkimg/ch_7/7_22_181_0.jpg)
工作原理:
DWP型属喷射气流带式干燥类型,热风以狭缝流或孔束流向下或上下同时喷向输送带上的物料,由于喷射气带高达15m/s以上,故对流传热的传热膜极薄,传热系数大,干燥速度快。该设备用于不透气类物料时,上面喷射气流仍返回上面,下面喷出的气体仍返出下面,再参与循环。对透气性物料如涂膜布干燥等,也适用于片状物料及一些特殊物料的干燥。如果采用双向气流喷射,板材之类物料干燥后变形小。喷射气流干燥使用热源可以是蒸气、电、热风炉及燃油烟道气等。
应用范围:
喷射气流带式干燥专用设备,比如纸浆干燥一般为S型或M形结构的多层式,大型纸浆模则为单层式。前者输送为吊蓝型,后者为为网带输送型。并且热风温度、循环气体量、湿度、气流速度及气流束形式不为其它物料所通用,实际差别很大。
对用户的咨询,我厂工程师会迅速作出详细的合理的设计方案,愿与用户一道,促使我们的设备性能更好,效益更好。
![](/picture/bkimg/ch_7/7_22_181_1.jpg)
技术参数:
名称\参数\序号 | DWP-Ⅰ | DWP-Ⅱ | DWP-Ⅲ | |
带宽m | 1.6 | |||
干燥段长m | 8 | |||
铺料厚mm | 10-80 | |||
使用温度oC | 50-120 | |||
蒸汽压力Mpa | 0.2-0.6 | |||
换热面积m2 | 330 | 296 | 259 | |
干燥时间h | 0.2-1.2 | |||
风机数量 | 3 | 2 | 2 | |
传动机功率Kw | 0.75 | |||
风机功率 KW | 7.5*3*2 | 7.5 3 | 7.5 3 | |
外形尺寸 | 10*2.1*3.6 |
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条