1) Pressured extraction
压力浸取
2) Extraction with aqua regia
高压浸取
3) pressure infiltration
压力浸渗
1.
The superplastic characteristics of the betaSiC whisker reinforced LY12 aluminum composite, fabricated by pressure infiltration and hotrolling after extrusion with a low extrusion ratio, were investigated The results show that the SiCw/LY12 composite exhibit a total elongation of 200%370% in the initial strain rate region from 33103 to 33102 s1at 788808
对压力浸渗、小挤压比挤压以及进一步轧制制备的β－ＳｉＣ晶须增强ＬＹ１２铝基复合材料的超塑性变形行为进行了研究。
2.
The scientific and technical matters concerned with the stability and the rheology properties of SiC slips, the packing behaviors of SiC powders, the manufacture of SiC tape and bulk skeletons, and the process of pressure infiltration were investigated.
研究了ＳｉＣ料浆的稳定性和流变特性、ＳｉＣ粉末的填实过程、ＳｉＣ薄带和骨架的制备技术、ＳｉＣ的固相烧结和骨架密度的控制，以及压力浸渗等科学问题和工艺问题。
3.
The article discussed the effect of preparing particle reinforced metal matrix composites by the path of pressure infiltration and the way of "nonuniform reinforced" to reduce the critical osmotic pressure and deformation degree of prefabricated body; and the possibility of improve plasticity and toughness of complex material to certain degree was also discussed.
本文通过“非均匀增强”的方式，探讨了用压力浸渗法制备颗粒增强金属基复合材料的途径，对减小临界浸渗压力及降低预制体变形程度的效果，以及在一定程度上改善复合材料塑性和韧性的可能性。
4) submurged pressure
浸水压力
1.
Influence of submurged pressure and acid sollution on loess collapsibility;
浸水压力及酸性溶液对黄土湿陷的影响
5) immersing oil under pressure
压力浸油
6) infiltration by pressure
压力熔浸
补充资料：槽式浸取
分子式：
CAS号：
性质：又称槽式浸取，在浸取槽内的固体物料(金属矿物、药物、天然植物的籽粒等)被浸取溶剂(水、酸或碱液、有机溶剂等)浸出有价组分的浸取过程。可以用固体颗粒处于静止状态的浸取设备，如渗滤浸取槽；也可以用固体颗粒处于悬浮状态(浆料)的浸取设备，如机械搅拌浸取槽、气升式搅拌浸取槽(帕丘卡槽)等。
CAS号：
性质：又称槽式浸取，在浸取槽内的固体物料(金属矿物、药物、天然植物的籽粒等)被浸取溶剂(水、酸或碱液、有机溶剂等)浸出有价组分的浸取过程。可以用固体颗粒处于静止状态的浸取设备，如渗滤浸取槽；也可以用固体颗粒处于悬浮状态(浆料)的浸取设备，如机械搅拌浸取槽、气升式搅拌浸取槽(帕丘卡槽)等。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条