1) layered back filling
分层吹填
1.
Technology of layered back filling in coast reclamation project;
围海造陆工程中分层吹填工艺的研究
2) stoping and filling
分层充填
1.
Developing process of stoping and filling from overhand level cut and fill stoping,two stoping primary filling to quick filling uninter pillar continuos stoping in Fenghuangshan Copper Mine are reviewed.
综述凤凰山铜矿充填采矿法从上向水平分层充填法 ,两步回采一次充填到无间柱连续开采快速充填等工艺的发展过程。
3) layered backfills
分层填土
1.
Based on the method of level-layer analysis,with the sliding harmonious condition of layered backfills considered,the theoretical answers to the earth pressures,the resultant earth pressures and the points of application of the resultant earth pressures on retaining walls with layered backfills are set up.
基于水平层分析法,考虑墙后分层填土的滑动变形协调条件,建立了关于墙后分层填土的挡土墙土压力强度、土压力合力和合力作用点的理论公式,并与库仑理论公式进行了比较分析。
2.
Based on soil plasticity and limit analysis theory,together with sliding harmonious condition of layered backfills,calculating method of active soil pressure on retaining wall with layered backfills is proposed,and corresponding conclusions are also made in this paper.
基于土的塑性极限分析理论 ,考虑墙后分层填土的滑动变形协调条件 ,探讨了分层填土作用在挡土墙上主动土压力的计算方法 ,得出了一些有益的结
3.
Based on the method of level-layer analysis,together with sliding harmonious condition of layered backfills,the theoretical answers to the unit earth pressures,the resultant earth pressures and the points of application of the resultant earth pressures on retaining wall with layered backfills are set up.
基于水平层分析法,考虑墙后分层填土的滑动变形协调条件,建立了关于墙后分层填土的挡土墙土压力强度、土压力合力和合力作用点的理论公式,并于库仑理论公式进行了比较分析。
4) layered tamping
分层填塞
1.
The basic theories of layered charging and layered tamping and the influences of explosive specific charge on distribution of explosive rock blocks for medium and deep hole blasting are discussed.
以两个装药层为例阐述中深孔爆破中分层装药分层填塞的基本原理以及炸药单耗对分层装药结构和爆岩块度的影响,并借助爆炸应力波理论和爆生气体膨胀理论分析合理进行分层装药分层填塞对于中深孔控制松动爆破爆炸效果的影响。
5) layer
[英]['leɪə(r)] [美][lɛr]
分层填充
1.
Experimental study on electrodeionization module with layer bed filling form;
树脂分层填充EDI膜堆实验研究
补充资料：多层吹塑
分子式：
CAS号：
性质：为了满足制品对气体、液体特殊的渗透要求加工“多层壁”中空容器的工艺。通常采用不同种塑料经特殊机头或多层注射机加工出多层型坯，然后经吹塑得到制品。工艺分共挤型坯吹塑及多层注坯吹塑。
CAS号：
性质：为了满足制品对气体、液体特殊的渗透要求加工“多层壁”中空容器的工艺。通常采用不同种塑料经特殊机头或多层注射机加工出多层型坯，然后经吹塑得到制品。工艺分共挤型坯吹塑及多层注坯吹塑。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条