1) cut point measurement
断点测试
2) optical fiber fault locator
光纤断点测试仪
3) cut point
断点
1.
This paper discusses the correlation between the number of cut points,granular entropy and classification accuracy in discretization.
研究离散化方案中断点数、粒度熵与分类精度之间的关系,证明了粒度熵随着断点数的增加而下降。
2.
This paper analyzed the current attribute discretization methods,and put forwards a cut point set computing algorithm.
在分析当前研究中常用的属性离散化方法的基础上,提出了一种计算初始断点集合的算法;定义了断点的信息熵,并以此作为对断点重要性的度量,提出了一种基于粗糙集理论和信息熵的属性离散化算法。
3.
In this paper a discretization algorithm based on importance of cut point.
提出一种基于断点重要性的离散化算法。
4) breakpoint
断点
1.
On "Narrative Breakpoint" in Contemporary Chinese News Reporting;
中国当代新闻报道的“叙事断点”研究
2.
A new discretization algorithm based on fuzzy rough set with the number of breakpoints reduced is put forward and discussed,taking account of the supportability and confidence of its rules and the relation between them.
提出和探讨了一种新的基于模糊粗糙集和断点简约化的离散化方法。
3.
in the process of thinning the fingerprint map,the feature points always become breakpoints.
中心扫描细化算法是一种基于方向的细化算法,具有较快的速度;在细化后的指纹图像中,其特征点往往成为断点,提出了一种基于细化后形成的断点和纹线方向的特征提取算法,运用中心扫描细化算法成功提取细节特征的基础上,运用极坐标转换、图像的旋转和可变界限盒原理,完成了指纹特征匹配算法;证实了基于中心扫描的指纹特征提取算法的可行性,并取得了很好的效果。
5) breaking point
断点
1.
The paper introduced a method that can locate the position of cable breaking point by using the reflection of low pressure impulse,and set up a control system through 89C52.
介绍了一种利用低压脉冲反射法测定电缆断点位置的方法,并采用89C52单片机建立了控制系统。
2.
In this method, the main purpose was emphasizing the decision rules, the main means was selecting the important breaking points, and the iterative constraint was the quality of classification.
本算法以突出信息表的决策规则为主要目的,选取重要断点为主要手段,以分类质量作为迭代约束条件。
6) broken point
断点
1.
The paper studies the theory about the corrosion as well as the broken point of the grounding grid in power plants and substations.
对发、变电站接地网腐蚀和断点的诊断理论进行了研究。
参考词条
补充资料:测试结果可接受性的检查和最终测试结果的确定
测试结果可接受性的检查和最终测试结果的确定
check of the acceptability of test results and determination of the final test result
C凡(3)二3.3d,时,取此3个结果的平均值作为最终侧试结果;否则取它们的中位数作为最终测试结果。。,为重复性标准差(即在重复性条件下所得侧试结果的标准差)。 在口田T 11792一1989中还对重复性和再现性条件下所得侧试结果可接受性的检查方法和最终测试结果的确定做了详细讨论和规定。(马毅林)ceshi 11叩uo kejieshCxjxing d6 iiancha he zuizhong ceshi】i闪旧de que心ing测试结果可接受性的检查和最终测试结果的确定(checkof山eac,ptability of test,ults助ddsterminationofthefi耐testresult)在商品检验中进行一次测试的情形不多见,当得到一个测试结果时,所得结果不可能直接与给定的重复性标准差作可接受性的检查。对测试结果的准确性有任何疑问时都应再进行一次测试。所以,对两个测试结果进行可接受性的检查是一般的情况。 可接受性的检查,实际上是一种统计检验。任何两个测试结果只要能通过可接受性的统计检验即可认为是一致的,均可接受。比如,在重复性条件下,所得结果之差的绝对值(下称绝对差)不超过相应的重复性限r(见重复性和再现性)的值,则认为两个结果是一致的,均可接受;如果两个侧试结果的绝对差超过r,则认为它们是不一致的,必须增加测试。 按国家标准《测试方法的精密度在重复性或再现性条件下所得测试结果可接受性的检查和最终测试结果的确定》(GBIT 1 1792一1989),在重复性条件下,如果两个测试结果的绝对差不超过r的值,可取两个侧试结果的平均值作为最终测试结果。如果两个结果的绝对差超过r的值,并且测试费用较低,须再做两次测试。当4个结果的极差(即其中的最大值与最小值之差)不超过相应的临界极差c,瓜(4)二3.6a,时,取4个结果的平均值作为最终测试结果。如果两个结果的绝对差超过r的值,并且测试费用较高时,只须再作一次测试。当3个结果的极差不超过相应的临界极差
说明:补充资料仅用于学习参考,请勿用于其它任何用途。