说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 慢漏快检
1)  fast examination of chronic gas leak
慢漏快检
1.
The theory and results of the fast examination of chronic gas leak were emphatically introduced in this article.
文中 ,重点介绍了“慢漏快检”的原理及其检测结果 ;其后 ,从理论上分析了这类管子的早期失效机理并对相关问题进行了讨论。
2)  leak detection instrument
快速检漏仪
1.
Study of on line leak detection instrument in automotive fuel oil system;
汽车燃油系统在线快速检漏仪的研究
3)  check of leakage
检漏测漏
4)  leak detecting
检漏
5)  leakage detection
检漏
1.
Due to the influence of various factors in the production,the graphite tubes are prone to damage and the leakage detection is difficult,so there are high requirements for the quality of tube replacement.
管壳式石墨换热器是湿法磷酸装置浓缩工序的关键设备 ,生产中因各种因素影响 ,石墨管易损坏 ,检漏较麻烦 ,对换管的质量要求较高。
2.
According to the problems discovered at leakage detection of wrapping for GIS switchgear in the process of GIS equipment installation,and combined with the general method of leakage detection of wrapping for GIS switchgear in the project,Beijing Electric Power Co.
北京电力公司根据多年来在安装GIS设备过程中,对GIS设备包扎检漏时发现的问题,结合工程中常用的GIS包扎检漏的方法,总结出了一种有效的直接对密封端进行包扎检漏的方法。
3.
This paper introduces a method of leakage detection by utilizing helium mass spectrometer leak detector and the comprehensive treatments based on the leakage detection for the vacuum system of a K-55-8.
8型汽轮机真空系统利用氦质谱检漏仪对漏点的检测方法及综合治理措施,取得了良好的效果。
6)  Leak hunting
检漏
1.
According to characteristics of equipments made of titanium-steel and titanium-stainless steel clad plates , associating with production , this paper introduces some methods of leak hunting for the kind of equipment , and briefly analyzes their advantages and disadvantages.
针对钛 钢、钛 不锈钢复合板制造设备的特点 ,结合生产实际 ,归纳出了此类设备检漏常见的几种方法 ,并简要分析了其优缺点。
2.
Aiming at the domestic application status of coolant charging-up and existing problems,this paper proposes a dsPIC30F3014 based control system design uses for mobile coolant charging-up device,which adopts microcomputer control based measurement technology and differential pressure leak hunting principle to realize digitalizing ration charging-up and leak hunting.
针对目前国内冷媒填充使用状况和存在的问题,利用微电脑控制计量技术和差压检漏原理进行数字化定量填充及检漏,提出了基于单片机dsPIC30F3014的汽车冷媒填充装置控制系统设计方案,给出系统硬件组成结构和软件设计思想,详细介绍了关键电路的工作原理,对系统的抗干扰措施进行了讨论。
补充资料:检检
1.有法度貌。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条