1) cladding
[英]['klædɪŋ] [美]['klædɪŋ]
熔敷
1.
A new coaxial feed laser cladding system without carrying gas is researched.
在二维平面上熔敷消除了方向性影响 ,多层激光熔敷组织、成分及硬度分布均匀。
2.
The influence of irradiation manner of a YAG pulsed laser on the microstructure and cracking behavior of claddings was characterized.
采用Nd:YAG固体脉冲激光器,在镍基高温合金上激光熔敷镍基自熔合金,对激光多次辐照条件下熔敷层的开裂问题进行了探索性研究。
2) deposited metal
熔敷金属
1.
Influence of gas content on impact toughness of deposited metal of martensitic stainless steel;
气体含量对马氏体不锈钢熔敷金属冲击性能的影响
2.
Effects of nonmetallic inclusions on acicular ferrite nucleation in deposited metals of microalloyed steel;
夹杂物对微合金钢熔敷金属针状铁素体形核的影响
3.
Research of M-A component in 9%Cr-1%Mo deposited metal;
9%Cr-1%Mo耐热钢熔敷金属中M-A组元的研究
3) deposition rate
熔敷率
1.
Accordingly the deposition rate is increased,and the weld formation is improved.
与常规钨极氩弧焊的对比分析表明,由于双钨极氩弧焊降低了电弧压力,提高了焊丝的熔敷率,因而在大电流高速度焊接时,极大地减少了凹坑、咬边等缺陷,实现了良好的焊缝成形,从而改善了常规钨极氩弧焊不适合大电流高速度焊接的不足,拓宽了钨极氩弧焊的使用范围,提高了焊接生产率。
2.
Owing to high deposition rate, excellent surface appearance, invisible arc, and lower welder skill requirement, the submerged-arc welding (SAW) process is used widely in the fabrication of pressure vessels, marine vessels, pipelines and offshore structures.
埋弧自动焊由于其熔敷率高,表面成形良好,焊接电弧不可见以及较低的焊工技能要求,因此被广泛应用于压力容器,潜艇,管道和海上结构建造中。
3.
Macro cross-sections of welded joint and deposition rate of wire metal that under different process were compared,it has analysed the microstructureof welded joints,tested the micro-hardness of weld joints,room temperatur
比较了不同工艺条件下接头的宏观断面、焊丝金属的熔敷率,分析了接头金属的显微组织,测试了接头金属的显微硬度,进行了接头的常温拉伸、冲击和高温拉伸试验。
5) Cu cladding layer
铜熔敷层
6) deposit metal
熔敷金属
1.
According to the introduction of the manufacture process feature of flux-cored wires and the good performances exhibited by the deposit metal,the current questions on the popularization and application of flux-cored wires were analyzed,as well as the applied methods of flux-cored wires for manual welding.
通过对药芯焊丝制造工艺特点及其熔敷金属所表现出的良好性能的介绍,分析了当前药芯焊丝推广应用所遇到的问题,提出了将药芯焊丝用于手工焊接的方法,并指出了推广应用的几个关键问题。
补充资料：热熔敷
分子式：
CAS号：
性质：又称热熔敷，熔融涂布。将一些有机物，如沥青、石蜡、聚乙烯、聚丙烯、聚酰胺和聚酯等树脂类加热熔融为液体，对基材进行涂布。涂布在绝热状态下进行，用刮刀计量整饰，涂布后的纸幅经冷却器或冷缸冷却，熔融涂料在基上形成涂层，再经卷取加工成成品。特点是无环境污染，作布速度快。
CAS号：
性质：又称热熔敷，熔融涂布。将一些有机物，如沥青、石蜡、聚乙烯、聚丙烯、聚酰胺和聚酯等树脂类加热熔融为液体，对基材进行涂布。涂布在绝热状态下进行，用刮刀计量整饰，涂布后的纸幅经冷却器或冷缸冷却，熔融涂料在基上形成涂层，再经卷取加工成成品。特点是无环境污染，作布速度快。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条