1) pairwise testing
![点击朗读](/dictall/images/read.gif)
成对测试
1.
Scheme for GUI test case generation based on pairwise testing and its implementation
![点击朗读](/dictall/images/read.gif)
基于成对测试的GUI测试用例生成方案及实现
2.
This algorithm, based on the principles of pairwise testing, considers all possible values and their combinations on extern interfaces of a system.
在对嵌入式软件进行黑盒测试研究的基础上,提出了一种基于成对测试设计思想的测试用例生成算法。
3.
Pairwise testing which bases on specifically testing criterion and study the approach of testing case.
测试用例生成是软件测试的关键 ,成对测试是根据特定的测试原则研究测试用例的产生方法。
2) Object-oriented integration testing
![点击朗读](/dictall/images/read.gif)
面向对象集成测试
1.
Object-oriented integration testing emphasizes on the problems such as whether the performances of the activating methods are right and whether the order of methods or messages is legal.
面向对象集成测试的重点在于检测消息能否正确地激活方法的执行,方法/消息序列是否合法等问题。
3) Object-Oriented Software Integration Testing
![点击朗读](/dictall/images/read.gif)
面向对象软件集成测试
4) pair-wise covering test
![点击朗读](/dictall/images/read.gif)
成对组合覆盖测试
1.
The technology of pair-wise covering test with parameters is an effective way in the software test.
参数的成对组合覆盖测试技术是软件测试中有效的测试方法之一。
5) contrastive test
![点击朗读](/dictall/images/read.gif)
比对测试
1.
The selection and analysis of uniformity of devastating contrastive test sample were introduced and the uniformity of corrugated cardboard s marginal pressure strength was analyzed.
对瓦楞纸板边压强度测试进行均匀性分析,介绍了破坏性比对测试样品的选用和均匀性分析方法。
补充资料:测试结果可接受性的检查和最终测试结果的确定
测试结果可接受性的检查和最终测试结果的确定
check of the acceptability of test results and determination of the final test result
C凡(3)二3.3d,时,取此3个结果的平均值作为最终侧试结果;否则取它们的中位数作为最终测试结果。。,为重复性标准差(即在重复性条件下所得侧试结果的标准差)。 在口田T 11792一1989中还对重复性和再现性条件下所得侧试结果可接受性的检查方法和最终测试结果的确定做了详细讨论和规定。(马毅林)ceshi 11叩uo kejieshCxjxing d6 iiancha he zuizhong ceshi】i闪旧de que心ing测试结果可接受性的检查和最终测试结果的确定(checkof山eac,ptability of test,ults助ddsterminationofthefi耐testresult)在商品检验中进行一次测试的情形不多见,当得到一个测试结果时,所得结果不可能直接与给定的重复性标准差作可接受性的检查。对测试结果的准确性有任何疑问时都应再进行一次测试。所以,对两个测试结果进行可接受性的检查是一般的情况。 可接受性的检查,实际上是一种统计检验。任何两个测试结果只要能通过可接受性的统计检验即可认为是一致的,均可接受。比如,在重复性条件下,所得结果之差的绝对值(下称绝对差)不超过相应的重复性限r(见重复性和再现性)的值,则认为两个结果是一致的,均可接受;如果两个侧试结果的绝对差超过r,则认为它们是不一致的,必须增加测试。 按国家标准《测试方法的精密度在重复性或再现性条件下所得测试结果可接受性的检查和最终测试结果的确定》(GBIT 1 1792一1989),在重复性条件下,如果两个测试结果的绝对差不超过r的值,可取两个侧试结果的平均值作为最终测试结果。如果两个结果的绝对差超过r的值,并且测试费用较低,须再做两次测试。当4个结果的极差(即其中的最大值与最小值之差)不超过相应的临界极差c,瓜(4)二3.6a,时,取4个结果的平均值作为最终测试结果。如果两个结果的绝对差超过r的值,并且测试费用较高时,只须再作一次测试。当3个结果的极差不超过相应的临界极差
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条