说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 修正的常数模算法
1)  DFE modified constant mode algorithm
修正的常数模算法
2)  MCMA algorithm
修正常系数模板算法
1.
To solve the problem of slow convergence in the modified constant modulus algorithm (MCMA), a variable step and dual mode blind equalization algorithm is proposed, based on the MCMA algorithm.
为解决修正常系数模板算法(MCMA)收敛速度缓慢的问题,在MCMA算法的基础上,给出了一种变步长双模式MCMA算法。
3)  modified constant modulus
修正常数模
1.
Towards the time-varying Doppler underwater acoustic channels, a modified constant modulus fractionally-spaced decision- feedback equalization and secon.
同时,针对水声信道的时变多普勒特性,在分数间隔判决反馈结构的基础上,提出了一种修正常数模分数间隔判决反馈盲均衡与二阶数字锁相环相结合的盲均衡算法,以纠正信道引入的载波相位旋转。
4)  Modified proportional factor method
修正比例常数法
5)  constant modulus algorithm
常数模算法
1.
At present,constant modulus algorithm (CMA) is widely used,but it has disadvanta- ges that the convergence speed is slow and the residual error is large.
目前,常数模算法(constant modulus algorithm,CMA)应用非常广泛,但它存在收敛速度慢,剩余误差大的缺点。
2.
Constant modulus algorithm is a most popular algorithm and is widely used for blind equalization of non-constant envelope signals and constant envelope signals.
常数模算法是一种最为常用的盲均衡算法,普遍应用于恒包络信号和非恒包络信号的均衡,但存在收敛速度慢和剩余误差大的缺点。
3.
To overcome the disadvantages of slow convergent rate and large residual mean square error (MSE) of constant modulus algorithm (CMA) and least mean kurtosis CMA, a square kurtosis cost function is defined as a kurtosis factor of error signals and its performance is analyzed, a least square kurtosis CMA for updating weight vectors of blind equalizer is proposed.
结果表明 :该算法在收敛速度 ,收敛后的均方误差及码间干扰等方面的性能优于常数模算法与最小平均峭度恒模算法。
6)  CMA
常数模算法
1.
In particular, the Constant Modulus Algorithm (CMA) has become a favorite of practitioners.
常数模算法(CMA)是实际中应用最广的一种盲均衡算法。
2.
Based on the constant modular algorithm (CMA), a new type of blind equalizer wit h filtering in discrete cosine transformation (DCT) domain is proposed for the amplitude- and phase-modulated digital communication systems.
在常数模算法 (CMA)基础上 ,提出一种适合于多电平调幅、调相数字通信系统的基于离散余弦变换(DCT)域滤波的新型CMA盲均衡器 。
3.
The problem was tackled with an evolutionary programming strategy, in which the order, as well as the taps of the equalizer were evolved simultaneously with the objective function of constant modulus algorithm (CMA) adopted a.
利用模拟浅海水声信道数据进行的仿真实验结果表明:本算法可有效避免常数模算法在低估阶数时造成的性能下降,适用于未知阶数情况下的信道盲均衡。
补充资料:凹模、凸凹模工作型面加工工艺过程
1)备料。 n
    2)锻造。锻成长方形的坯料(每件留长工艺夹头)。 n
    3)热处理。退火。   n
    4)铣(刨)削。铣(刨)削六面成长方形模块。 n
    5)磨削。磨削上、下两端面及相邻两侧面,用90。角尺测量相邻两面的垂直度。 n
    6)钳工加工。用平板和划线盘按图划线,并打样冲眼;用钻头钻螺纹底孔;用圆柱销孔的预孔;用钻头钻挡料销让位孔;用钻头在中心处钻穿丝孔等;正、反面孔口倒角;凸凹模用钻头孔扩,保证刃口高度;攻螺纹;铰孔。n
  7)铣削。平口钳装夹工件;用的立铣刀铣削型孔至尺寸,保证深度。 n
   8)热处理。凹模工件淬硬至HRC60~64,凸凹模工件淬硬至HRC58~62。 n
   9)平磨。磨上、下两端面及相邻两侧面,用90。角尺测量相邻两面的垂直度至图要求;退磁。 n
   10)线切割。按图编制线切割程序,切割模型孔成形,留单面研磨余量0.005 mm。 n
   11)钳工加工。研光线切割面: n
   12)检验。 n复合冲裁模的装配应选择凸凹模作为装配基准件,先装下模部分,后装上模部分
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条