1) LiBq_4/ITO
LiBq4/ITO
1.
As the states of the interface between organic layer and electrode and the film quality of (organic) layer affect the properties of OLEDs, we investigated the surface and interface states of LiBq_4/ITO by using atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS).
用原子力显微镜(AFM)研究了LiBq4/ITO样品表面形貌,结果表明LiBq4层中存在很多裂缝和空隙。
2) LiBq_4
LiBq4
1.
Devices with the structure of ITO/CuPc/TPD/LiBq_4/Alq_3/LiF/Al,LiBq_4 used as an active layer,were prepared.
制备了以LiBq4 为发光层 ,结构为ITO/CuPc/TPD/LiBq4 /Alq3 /LiF/Al的器件。
3) ITO powder
ITO粉
1.
The measurement of in tin content in the ITO powder material;
ITO粉末材料中铟含量的测定
4) ITO film
ITO膜
1.
The ITO films with resistivity below 2×10 -4 Ω·cm and visible light transmissivity beyond 80% were obtained.
所镀制的ITO膜电阻率已降到 <2× 10 - 4Ω·cm ,可见光透过率达 80 %以上。
2.
In this study, Pb~+ ions were injected into the ITO film on glass by ion-implantation technology.
采用离子注入技术将铅离子注入到ITO薄膜玻璃中,用分光光度计、四探针测试仪、硬度计等测定了ITO膜注入前后的光学性能、电学性能、机械性能和化学德定性。
3.
This paper described investigation of the transparency and electroconductive mechanism of semiconductive oxide ITO film,use reactive direct current magnetic control sputting coating process,to coating an ITO film on the acrylic glass at lower temperature.
通过探讨半导体氧化物ITO膜的透光和导电机理,用反应性直流磁控溅射的镀膜工艺,在有机玻璃上低温镀制(ITO)膜,研究ITO膜溅射工艺参数与透光和导电性能的关系,实现了在低温下镀制(ITO)膜的技术,其透光率≥80%以上,表面电阻≤30Ω/□。
5) ITO films
ITO膜
1.
The resistivity of ITO films was minimised by optimizing the tin doping concentration in the solution.
以铟、锡氯化物为前驱物,采用溶胶-凝胶法在玻璃基体上制备不同锡掺杂的ITO膜,在热处理温度为450℃条件下制备不同锡掺杂(质量分数11%~33%)的ITO膜,研究锡掺杂对ITO膜方阻和结构特性的影响。
2.
Transparent and conductive ITO films had been prepared by the sol gel process, and the effects of every factor on the optical and electrical properties of the files had been investigated during the process.
采用溶胶 凝胶方法制备ITO膜 ,并从制备工艺上研究了各种因素对ITO膜光电特性的影响 最后制出的ITO膜厚度约为 5 0nm ,在可见光区平均透射比达 97% ,最高达 99。
3.
The advantages of the technique include higher quality ITO films growth, stronger (3.
与未经在线等离子体清洗的基片沉积的ITO膜相比 ,膜层附着力提高了 3。
6) It o∧-type
Ito∧型
补充资料：Ito导电膜玻璃
ito导电膜玻璃
ito导电膜玻璃
氧化铟锡(indium-tin oxide)透明导电膜玻璃,多通过ito导电膜玻璃生产线,在高度净化的厂房环境中,利用平面磁控技术,在超薄玻璃上溅射氧化铟锡导电薄膜镀层并经高温退火处理得到的高技术产品。
产品广泛地用于液晶显示器(lcd)、太阳能电池、微电子ito导电膜玻璃、光电子和各种光学领域。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。