1)  landmark
方位参考点
2)  azimuth
方位
1.
A slim azimuth 20 independent-arm caliper logging tool;
小直径方位二十独立臂井径测井仪
2.
Design of TFY-1 universal azimuth jointer with a restrained gyroscope;
TFY-1型框架陀螺方位通用短接设计
3.
The pit shaft parameters of the elevation angle,the azimuth angle,the tool of facial angle and so on are obtained after the computation.
陀螺测斜技术以动力调谐速率,陀螺测量地球自转角速率分量和石英加速计测量地球加速度分量为基础,经计算得出井筒的倾斜角、方位角、工具面角等参数。
3)  orientation
方位
1.
Climate Orientation and Building Surface Energy Efficiency——Research on Building Surface s Climate Resources Utilization Technology Strategy;
气候方位与建筑表皮节能——建筑表皮的气候资源利用技术策略研究
2.
Design of Orientation Sensor based on Fluxgate Technique;
基于磁通门技术的方位传感器设计
3.
Influence of Orientation of Wollaston Prism on Accuracy of Laser Interference Measuring System;
Wollaston棱镜方位对激光干涉测量精度的影响
4)  position
方位
1.
Distribution of Reflecting Energy Varying with Different Position of Cube-corner Prism;
角锥棱镜不同方位反射光束的能量分布
2.
In a measuring angle of laser interferometer,the different positions of the cube-corner prism make the range of the measuring angle of this instrument changed.
在激光测角干涉仪中,由于角锥棱镜在安置方位的不同,将导致该仪器角度测量范围的变化。
3.
These regulations are explained in three aspects, respectively of space, position and shape, which form the basic architectural regulations.
中国古典戏剧由于其演出空间与活动方式具有多样性与多变性的特点,作为一种具有特定功能的建筑,它们体现出一定的类的规定性,这种规定性从空间、方位、造型三个方面表现出来,从而形成中国古代剧场的基本规制。
5)  bearing
方位
1.
The research of underwater passive TMA algorithm with bearings and frequencies measurements;
基于方位频率测量的水下被动目标运动分析算法
2.
Research of underwater passive target motion analysis algorithm using both bearing and time-delay measurements;
一种基于方位时延的水下被动目标运动分析算法研究
3.
In this paper,the question of how to track underwater target using bearings and time-delay is presented and analyzed.
在对利用方位和声波脉冲到达时间差的被动测量来进行目标的定位和跟踪后 ,对系统进行了描述和分析 ,利用递推最小二乘 (RL S)估计算法估计出目标的运动偏量 ,然后结合线性卡尔曼滤波 (KF)算法给出目标的运动状态。
6)  direction
方位
1.
Qualitative Spatial Reasoning about Topology and Cardinal Direction;
结合拓扑和方位的定性空间推理方法
2.
In this paper,we study three groups of direction discourse in Peotry,they are"left and right","four direction"and"south mountain".
本文选取了《诗经》中的三种方位话语“左右”、“四方”和“南山”为考察对象,探究这些方位话语在古代社会生活中的运用方式、基本特点及文化意蕴,揭示出方位观的演变与中国古代诗学及社会文化之间的密切关系。
3.
Subjects read narratives describing directions of objects around an upright observer, who was periodically reoriented, and given a description of the objects in different positions around his body.
用因素实验证明,在故事阅读产生的想象场景中,位于其中的观察者对身体四周物体的搜索分为两个阶段:第一阶段是目标方位的判断,认知加工时间的模式是前<后<左=右;第二阶段是注意指向目标方位,从而辨别目标物体,认知加工时间的模式是注意点<注意点对面<注意点左侧=注意点右侧。
参考词条
补充资料:闭式单点、双点压力机
代码:00413
设备名称:闭式单点、双点压力机
型号规格:公称力≥800kN
计量单位:台
主要参数内容
国际先进国内先进国内一般国内落后评定方法及说明
(一)加工精度
    参照GB10924-89、GB10933-89、JB5200-91
1、滑块下平面对工作台上平面的平行度(mm)
30%精度储备20%精度储备达到规定值大于规定值 
0.02+0.10/100×滑块下平面的被测长度
     
2、滑块行程对工作台上平面的垂直度
30%精度储备20%精度储备达到规定值大于规定值 
0.05+0.02/100×滑块行程长度
     
(二)结构性能
     
1、离合器、制动器接通率,当滑块行程次数≤16次/分时为70%,≤25次/分时为60%,≤45次/分时为50%
大于规定值10%大于规定值达到规定值达不到规定值 
2、液压超负荷保险装置、微调装置、吨位指示器
全部具有全部具有部分具有没有 
(三)噪声dB(A)
     
1、公称力≤400kN
≤85≤87≤88>88 
2、公称力>400kN
≤87≤88≤90>90 
说明:补充资料仅用于学习参考,请勿用于其它任何用途。